Defender (1999-2002). Manual — part 134
![](/vehicles/onond/ycatth/que/veke.png)
86
ELECTRICAL
8
REPAIR
LAMP - FRONT FLASHER
Service repair no - 86.40.42
Remove
1. Remove 2 screws securing flasher lamp to front
wing.
2. Disconnect multiplug and remove lamp.
Refit
3. Position flasher lamp and connect multiplug.
4. Fit and tighten lamp securing screws.
BATTERY - DISCONNECT - FROM 02MY
Service repair no - 86.15.99
Remove
1. Remove front seat cushion.
2. Release clip and remove battery cover.
3. Loosen bolt securing negative earth lead, do not
remove lead at this stage.
4. Fit ignition key, turn to position ’II’. Turn ignition
off, remove key from lock and immediately
remove negative lead.
Refit
5. Connect negative lead to negative terminal and
tighten bolt to 10 Nm (7 lbf.ft).
6. Fit and secure battery cover.
7. Fit seat cushion.
![](/vehicles/onond/ycatth/que/riapusifo.png)
ELECTRICAL
9
REPAIR
MOTOR & REGULATOR - FRONT DOOR - FROM
02MY
Service repair no - 86.25.03
Remove
1. Remove plastic sheet. See CHASSIS AND
BODY, Repair.
2. Lower glass and remove 2 bolts securing door
glass to regulator.
3. Release glass from regulator, raise and wedge
in raised position.
4. Disconnect multiplug from motor.
5. Remove 4 bolts and 2 nuts securing motor and
regulator assembly.
6. Release and remove motor and regulator
assembly.
Refit
7. Fit motor and regulator assembly, fit nuts and
bolts and tighten to 10 Nm (7 lbf.ft).
8. Connect multiplug to motor.
9. Remove wedges, lower glass and locate to
regulator. Fit bolts and tighten to 6 Nm (4 lbf.ft).
10. Raise and lower glass to check operation.
11. Fit plastic sheet. See CHASSIS AND BODY,
Repair.
![](/vehicles/onond/ycatth/que/erill.png)
86
ELECTRICAL
10
REPAIR
SWITCH - FASCIA - FROM 02MY
Service repair no - 86.25.18
Remove
1. Remove radio. See this Section.
2. Release switch, disconnect multiplug and
remove switch.
Refit
3. Connect multiplug to switch and fit switch to
panel.
4. Fit radio. See this Section.
HARNESS - FRONT DOOR - FROM 02MY
Service repair no - 86.25.20
Remove
1. Remove door lock solenoid. See this Section.
2. Carefully peel back section of plastic sheet for
access to harness.
3. Release clips securing harness to panel.
4. Disconnect multiplug from motor.
5. Release harness sleeve and withdraw harness
from door.
6. Release harness sleeve and withdraw harness
multiplugs from ’A’ post.
7. Disconnect 2 multiplugs and remove harness.
![](/vehicles/onond/ycatth/que/ousank.png)
ELECTRICAL
11
REPAIR
Refit
8. Position harness and connect multiplugs.
9. Feed multiplugs into ’A’ post and secure harness
sleeve.
10. Connect multiplug to motor.
11. Secure harness clips and sleeve.
12. Secure plastic sheet.
13. Fit door lock solenoid. See this Section.
SOLENOID/MOTOR - TAIL DOOR - FROM 02MY
Service repair no - 86.26.02
Remove
1. Remove tail door trim casing. See CHASSIS
AND BODY, Repair.
2. Disconnect multiplug from solenoid.
3. Remove bolt and screw securing solenoid to
door.
4. Release clip securing harness to solenoid
mounting bracket.
5. Remove solenoid assembly from operating rod.
6. Remove 2 screws securing solenoid to mounting
bracket.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст