Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 677
LI-31
License Plate Light
LIGHTING SYSTEM
25.License Plate Light
A: REMOVAL
1. 4 DOOR MODEL
1) Disconnect the ground cable from battery.
2) Remove the license plate light mounting screw
(A) and then remove the lens.
3) Remove the bulb.
4) Remove the trunk lid garnish. <Ref. to EI-73,
5) Remove the license plate light assembly har-
ness.
2. 5 DOOR MODEL
1) Disconnect the ground cable from battery.
2) Remove the license plate light while pushing it to
the left and pulling it.
3) Disconnect the harness connector, and remove
the socket (A).
4) Remove the bulb.
B: INSTALLATION
Install each part in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) Replace the bulb if it is found defective.
LI-00034
(A)
LI-00821
LI-00939
(A)
LI-32
High-mounted Stop Light
LIGHTING SYSTEM
26.High-mounted Stop Light
A: REMOVAL
1. 4 DOOR MODEL (STANDARD TYPE)
1) Disconnect the ground cable from battery.
2) Disconnect the high-mounted stop light connec-
tor.
3) Loosen the bolt, and remove the high-mounted
stop light assembly.
4) Remove the high-mounted stop light assembly
cover.
5) Turn the socket and remove the bulb.
2. 4 DOOR MODEL (WITH BUILT-IN REAR
SPOILER)
1) Disconnect the ground cable from battery.
2) Detach the rear spoiler. <Ref. to EI-42, REMOV-
3) Remove the screw, and remove the high-mount-
ed stop light.
3. 5 DOOR MODEL
1) Disconnect the ground cable from battery.
2) Remove the roof spoiler. <Ref. to EI-41, RE-
3) Remove the caps and screws, then remove the
high-mounted stop light.
B: INSTALLATION
Install each part in the reverse order of removal.
Tightening torque:
4 door model (standard type)
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
C: INSPECTION
1. 4 DOOR MODEL (STANDARD TYPE)
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) Replace the bulb if it is found defective.
2. EXCEPT FOR 4 DOOR MODEL (STAN-
DARD TYPE)
1) Install the high-mounted stop light to test if it illu-
minates normally.
2) If it fails to illuminate normally, replace the high-
mounted stop light with a new part.
NOTE:
Since LED (Light Emitting Diode) is used for the
high-mounted stop light, replace the high-mounted
stop light assembly if the LED burns out.
LI-00221
LI-01142
LI-01151
LI-00858
LI-33
Spot Map Light
LIGHTING SYSTEM
27.Spot Map Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the lens (A) and spot map light mount-
ing screws (B).
• Model without sunroof
• Model with sunroof
3) Disconnect the harness connectors and remove
the spot map light.
4) Remove the bulb.
B: INSTALLATION
Install each part in the reverse order of removal.
C: INSPECTION
1. SPOT MAP LIGHT BULB
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) Replace the bulb if it is found defective.
2. SPOT MAP LIGHT SWITCH
1) Remove the spot map light.
2) Check the resistance of spot map light.
• Model without sunroof
• Model with sunroof
3) Replace the spot map light if the inspection re-
sult is not within the standard value.
(A)
LI-00224
(B)
LI-00225
SR-00222
(A)
SR-00223
(B)
Switch position
Terminal No.
Standard value
OFF
1 and 2
1 MΩ or more
ON
1 and 2
18±5.4 Ω
LI-01100
1
2
3
4
5
6
LI-00363
2 1
LI-34
Room Light
LIGHTING SYSTEM
28.Room Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the lens (A) and room light mounting
screws (B).
3) Disconnect the harness connector and remove
the room light.
4) Remove the bulb.
B: INSTALLATION
Install each part in the reverse order of removal.
C: INSPECTION
1. ROOM LIGHT BULB
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) Replace the bulb if it is found defective.
2. ROOM LIGHT SWITCH
1) Remove the room light.
2) Measure the resistance between room light
switch terminals.
3) Connect terminal No. 3 to the battery positive
terminal and terminal No. 1 and No. 2 to the battery
ground terminal, and check room light operation.
4) Replace the room light if it is found defective.
LI-00315
(A)
LI-00316
(B)
Switch position
Terminal No.
Standard value
OFF
—
1 MΩ or more
ON
1 and 3
1.5±0.5 Ω
DOOR
2 and 3
1.5±0.5 Ω
Switch position
Light status
OFF
Light OFF
ON
Light ON
DOOR
Light ON
LI-00257
3 2 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст