Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 675
LI-23
Front Fog Light Bulb
LIGHTING SYSTEM
17.Front Fog Light Bulb
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the clips and turn over the mud guard.
3) Disconnect the bulb connector.
4) Rotate the bulb then detach the fog light bulb.
B: INSTALLATION
CAUTION:
Align the bulb tabs with the fog light securely,
push the bulb fully, and then rotate it.
Install each part in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) Replace the bulb if it is found defective.
LI-01139
LI-01127
LI-24
Side Turn Signal Light Assembly
LIGHTING SYSTEM
18.Side Turn Signal Light As-
sembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the mirror. <Ref. to GW-19, REPLACE-
3) Remove the scalp cap. <Ref. to GW-15, RE-
4) Remove the screws.
5) Disconnect the harness connector and remove
the side turn signal light assembly.
B: INSTALLATION
Install each part in the reverse order of removal.
C: INSPECTION
1) Install the side turn signal light assembly and
check that it blinks normally.
2) If it fails to blink normally, replace the side turn
signal light assembly with a new part.
NOTE:
Since LED (Light Emitting Diode) is used for the
side turn signal light, replace the side turn signal
light assembly if the LED burns out.
LI-00707
LI-25
Rear Combination Light Assembly
LIGHTING SYSTEM
19.Rear Combination Light As-
sembly
A: REMOVAL
1. 4 DOOR MODEL
1) Disconnect the ground cable from battery.
2) Remove the trunk room side trim. <Ref. to EI-63,
3) Disconnect the rear combination light connector.
4) Remove the nuts and detach the rear combina-
tion light.
2. 5 DOOR MODEL
1) Disconnect the ground cable from battery.
2) Remove the bolts, and then detach the rear
combination light by pulling it to the rear side of ve-
hicle.
3) Disconnect the harness connector and remove
the rear combination light.
B: INSTALLATION
Install each part in the reverse order of removal.
Tightening torque:
4 door model
4.5 N·m (0.46 kgf-m, 3.3 ft-lb)
5 door model
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
C: INSPECTION
1. 4 DOOR MODEL
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) Replace the bulb if it is found defective.
2. 5 DOOR MODEL
1) Install the rear combination light assembly and
check that it blinks normally.
2) If it fails to blink normally, replace the rear com-
bination light assembly with a new part.
NOTE:
Since LED (Light Emitting Diode) is used for the tail
light/stop light bulb, replace the rear combination
light assembly if the LED burns out.
LI-00834
LI-00817
LI-26
Tail/Stop Light Bulb
LIGHTING SYSTEM
20.Tail/Stop Light Bulb
A: REMOVAL
1. 4 DOOR MODEL
1) Disconnect the ground cable from battery.
2) Remove the trunk room side trim cover. <Ref. to
EI-63, REMOVAL, Trunk Room Trim.>
3) Turn the socket and remove the bulb.
2. 5 DOOR MODEL
The tail light/stop light bulbs use LEDs (Light Emit-
ting Diode) can not removed.
B: INSTALLATION
Install each part in the reverse order of removal.
C: INSPECTION
1. 4 DOOR MODEL
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) Replace the bulb if it is found defective.
2. 5 DOOR MODEL
NOTE:
Since LED (Light Emitting Diode) is used for the tail
light/stop light bulb, replace the rear combination
light assembly if the LED burns out.
LI-00835
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст