Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 743
EI-59
Upper Inner Trim
EXTERIOR/INTERIOR TRIM
21.Upper Inner Trim
A: REMOVAL
1) Remove the cap (B) on the upper side of the pil-
lar trim, and remove the bolt.
NOTE:
Remove the molding (A), and remove the cap from
the backside of pillar trim not to damage the trim.
2) Remove the front pillar upper trim.
3) Remove the front inside scuff plate, rear inside
scuff plate and center pillar lower trim. <Ref. to EI-
57, REMOVAL, Lower Inner Trim.>
4) Remove anchor bolt cover (A).
5) Loosen the shoulder anchor bolt (B), and then
detach the shoulder anchor from center pillar.
6) Remove the cap (B) on the upper side of the pil-
lar trim, and remove the bolt.
NOTE:
Remove the molding (A), and remove the cap from
the backside of pillar trim not to damage the trim.
7) Pull and remove the upper trim clip section of the
center pillar along with the lower trim.
8) Spread the lower trim outwards to remove the
claw, and pull on the upper trim to remove.
B: INSTALLATION
Install each part in the reverse order of removal.
Tightening torque
Refer to “COMPONENT” of “General Descrip-
tion”.
Upper inner trim: <Ref. to EI-21, INNER TRIM
(5 DOOR MODEL), COMPONENT, General
Seat belt anchor: <Ref. to SB-2, FRONT SEAT
BELT, COMPONENT, General Description.>
EI-02283
(B)
(A)
SB-00350
(A)
(B)
EI-02094
(B)
(A)
EI-02095
EI-01856
(1)
(2)
EI-60
Rear Quarter Trim
EXTERIOR/INTERIOR TRIM
22.Rear Quarter Trim
A: REMOVAL
1. 5 DOOR MODEL
1) Remove the rear seat. <Ref. to SE-13, REMOV-
2) Remove the seat belt lower anchor bolt.
3) Remove the cap (B) on the upper side of the rear
quarter pillar front trim, and remove the bolt inside.
NOTE:
Remove the molding (A), and remove the cap from
the backside of pillar trim not to damage the trim.
4) Remove the side belt cover (C).
5) Remove center belt cover (D), and remove the
anchor bolt inside.
6) Remove the clips and screws, and remove the
rear quarter upper trim.
7) Remove the luggage floor end cover.
8) Remove the bolts, and remove the rear quarter
lower trim.
SB-00353
EI-02284
(A)
(B)
EI-02285
(C)
(D)
EI-01950
EI-01816
EI-01817
EI-61
Rear Quarter Trim
EXTERIOR/INTERIOR TRIM
2. 4 DOOR MODEL
1) Remove the rear seat. <Ref. to SE-13, REMOV-
2) Remove the inside scuff plate. <Ref. to EI-57,
3) Peel the trim, and use a screwdriver, etc. to
press claw (A) of the metal clip, to remove the quar-
ter upper trim.
CAUTION:
If the metal clip comes off or becomes dam-
aged, replace both the quarter upper trim rear
and metal clips.
4) Remove the seat belt lower anchor bolt.
5) Remove the cap (B) on the upper side of the rear
quarter trim, and remove the bolt inside.
NOTE:
Remove the molding (A), and remove the cap from
the backside of pillar trim not to damage the trim.
6) Remove side belt cover (A).
7) Remove the bolts and clips, and remove the
quarter upper trim front.
8) Remove the rear seat. <Ref. to SE-13, REMOV-
9) Remove the clip of the trunk room side trim.
10) Remove the clips, then remove the quarter low-
er trim.
B: INSTALLATION
Install each part in the reverse order of removal.
Tightening torque
Refer to “COMPONENT” of “General Descrip-
tion”.
Rear quarter upper trim: <Ref. to EI-21, IN-
NER TRIM (5 DOOR MODEL), COMPONENT,
Seat belt anchor: <Ref. to SB-3, REAR SEAT
BELT, COMPONENT, General Description.>
EI-02326
(A)
SB-00353
EI-02291
(B)
(A)
EI-02292
(A)
EI-02327
EI-01906
EI-62
Rear Shelf Trim
EXTERIOR/INTERIOR TRIM
23.Rear Shelf Trim
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the rear quarter trim. <Ref. to EI-61, 4
DOOR MODEL, REMOVAL, Rear Quarter Trim.>
3) Remove the seat belt center anchor lower bolt.
(3-point type belt only)
4) Remove the high-mounted stop light. <Ref. to LI-
32, 4 DOOR MODEL (STANDARD TYPE), RE-
MOVAL, High-mounted Stop Light.>
5) Remove the clips, and remove the rear shelf
trim.
B: INSTALLATION
Install each part in the reverse order of removal.
SB-00425
EI-02329
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст