Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 753
EB-23
Rear Door
EXTERIOR BODY PANELS
B: INSTALLATION
1) Put a wooden block on jack and place the rear
door on that.
2) Apply grease to the moving part of door hinges.
3) Install the rear door to upper hinge and lower
hinge adjusting by jack.
4) Tighten bolt of door checker.
5) Connect door harness connector.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. <Ref. to EB-11, REAR DOOR, COMPO-
6) Install while paying attention to make a uniform
clearance around the rear door panel. For the di-
mension of clearance, refer to “SPECIFICATION”
in “General Description”. <Ref. to EB-2, SPECIFI-
C: ADJUSTMENT
1) Open the rear door, loosen the door-side bolts of
upper and lower hinges to align the position for ver-
tical and horizontal direction of rear door panel.
2) Loosen the screw (A) and tap striker (B) using
plastic hammer to adjust the gap between rear end
surface of rear door panel and body surface.
CAUTION:
Do not use an impact wrench. Welding area on
the striker nut plate is easily broken.
EB-00013
EB-00015
EB-00017
(B)
(A)
EB-24
Rear Sealing Cover
EXTERIOR BODY PANELS
8. Rear Sealing Cover
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the rear door trim. <Ref. to EI-46,
REAR DOOR, REMOVAL, Door Trim.>
3) Remove the rear speaker. <Ref. to ET-9, RE-
4) Remove the sealing cover.
CAUTION:
• Carefully remove the butyl tape. Excessive
force will easily break the cover.
• If the sealing cover gets broken, replace it
with a new part.
B: INSTALLATION
CAUTION:
• If the sealing cover gets broken, replace it
with a new part.
• Apply a butyl tape evenly.
• Attach the sealing cover, keeping it from be-
coming wrinkled.
• If the butyl tape is applied unevenly, it will
cause water leakage and soiling.
1) Install each part in the reverse order of removal.
2) When replacing the sealing cover, use the butyl
tape.
3) Press the butyl tape-applied area firmly to pre-
vent any floating on surface.
Butyl tape:
3M8626 or the equivalent
C: INSPECTION
If the sealing cover gets damaged, replace it with a
new part.
EB-00018
EB-25
Door Sash Tape
EXTERIOR BODY PANELS
9. Door Sash Tape
A: REMOVAL
1. FRONT DOOR
1) Disconnect the ground cable from battery.
2) Remove the front door trim. <Ref. to EI-45,
FRONT DOOR, REMOVAL, Door Trim.>
3) Remove the outer mirror assembly. <Ref. to
GW-16, REMOVAL, Outer Mirror Assembly.>
4) Remove the sealing cover. <Ref. to EB-21, RE-
5) Remove the front door glass. <Ref. to GW-12,
6) Remove the glass run rubber.
7) Remove the B pillar upper clip, and remove the
front door weather strip.
8) Remove the screws, and remove the front door
weather strip outer.
CAUTION:
• When removing the weather strip outer, be
careful not to damage the vehicle.
• If the weather strip outer is deformed, always
replace with a new part.
9) Peel the door sash tape from the door sash.
NOTE:
• If the tape is difficult to remove, warm the tape
with a hairdryer, etc. to make the removal easier.
Use a household hairdryer. Do not use industrial
dryers.
• If tape residue is remaining on the door sash,
wipe clean.
2. REAR DOOR
1) Disconnect the ground cable from battery.
2) Remove the rear door trim. <Ref. to EI-46,
REAR DOOR, REMOVAL, Door Trim.>
3) Remove the sealing cover. <Ref. to EB-24, RE-
4) Remove the rear door glass. <Ref. to GW-21,
5) Remove the glass run rubber.
6) Remove the B pillar upper clip, and remove the
front door weather strip.
7) Loosen the screws and clips to remove the gus-
set cover outer.
8) Remove the rear door weather strip outer.
CAUTION:
• When removing the weather strip outer, be
careful not to damage the vehicle.
• If the weather strip outer is deformed, always
replace with a new part.
EB-00423
EB-00398
A-A
A-A
EB-00424
EB-00399
EB-00400
A-A
A-A
EB-26
Door Sash Tape
EXTERIOR BODY PANELS
9) Peel the door sash tape from the door sash.
NOTE:
• If the tape is difficult to remove, warm the tape
with a hairdryer, etc. to make the removal easier.
Use a household hairdryer. Do not use industrial
dryers.
• If tape residue is remaining on the door sash,
wipe clean.
B: INSTALLATION
CAUTION:
• When applying tape, use a spatula, etc. to ap-
ply evenly, pushing it against the sash to make
sure that no air bubbles are formed.
If air bubbles are formed, reapply the tape.
• If the tape is wrinkled, etc. during application,
replace the tape.
• Turning points and ends of the tape will be a
cause for peeling if the pressure is insufficient
during application, so make sure to push down
on the tape firmly when applying.
• There are locations where the tape ends will
overlap each other. When applying the tape, be
careful of the order of their application.
• Front
• Rear
1. FRONT DOOR
1) Match the upper area of the gusset and the cut
area of the tape as shown in the figure. (Position of
the arrow)
EB-00407
(1)
(2)
EB-00409
(1)
(2)
(3)
(1) Front door sash tape - front
EB-00401
A-A
A-A
(1)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст