Subaru Legacy IV (2008 year). Service manual — part 740
5AT-84
Oil Pump Cover
AUTOMATIC TRANSMISSION
C: DISASSEMBLY
1. FRONT BRAKE
1) Remove the snap ring.
2) Remove the retainer plate, drive plate and driven
plate.
3) Using the ST1, ST2 and ST3, remove the snap
ring.
ST1
18762AA000
COMPRESSOR SPECIAL
TOOL
ST2
18765AA000
COMPRESSOR SUPPORT
ST3
18763AA000
COMPRESSOR SHAFT
4) Remove the retainer and return spring.
5) Remove the front brake piston using com-
pressed air.
6) Remove the D-ring from front brake piston.
2. OIL PUMP
1) Take out the oil pump housing.
2) Take out the oil pump body.
D: ASSEMBLY
1. FRONT BRAKE
1) Apply ATF to D-ring, and then install it to the
front brake piston.
2) Install the front brake piston to oil pump cover.
NOTE:
Install by aligning the “
” mark on front brake pis-
ton surface with the oil pump cover rib.
3) Install the retainer and return spring.
AT-01980
AT-01981
ST1
ST2
ST3
AT-02349
AT-01982
AT-02350
5AT-85
Oil Pump Cover
AUTOMATIC TRANSMISSION
4) Install the front brake piston assembly using
ST1, ST2 and ST3.
ST1
18762AA000
COMPRESSOR SPECIAL
TOOL
ST2
18765AA000
COMPRESSOR SUPPORT
ST3
18763AA000
COMPRESSOR SHAFT
5) Install the genuine driven plate instead of retain-
er plate, and temporarily assemble the drive plate
and driven plate.
Part No.
31536AA290
Driven plate
6) Install the snap ring.
7) Measure the clearance between retainer plate
and snap ring, and then select the suitable retainer
plate from table.
Front brake clearance specification:
0.7 — 1.1 mm (0.028 — 0.043 in)
8) Remove the snap ring, replace the drive plate
used in measurement of clearance with the retainer
plate, and then reassemble.
2. OIL PUMP
1) Apply ATF to oil pump assembly, and then install
it to oil pump housing.
2) Install the O-ring to oil pump cover.
3) Install the oil pump housing to the oil pump cov-
er.
Tightening torque:
10 N·m (1.0 kgf-m, 7.4 ft-lb)
Front brake retainer plate
Part No.
Thickness mm (in)
31567AB130
3.4 (0.134)
31567AB140
3.6 (0.142)
31567AB150
3.8 (0.150)
31567AB160
4.0 (0.157)
AT-01981
ST1
ST2
ST3
AT-01980
AT-01983
AT-01982
5AT-86
Oil Pump Cover
AUTOMATIC TRANSMISSION
E: INSPECTION
1. FRONT BRAKE
Check the following items.
• Drive plate facing for wear and damage
• Snap ring for wear, return spring for damage,
and retainer for damage
• Piston for damage
• D-ring for damage
2. OIL PUMP
Check the following items.
• Oil pump cover and oil seal for breakage or dam-
age
• Oil pump body for scratch or damage
1) Check the seal ring and oil seal for breaks and
damage.
2) Check other parts for dents or faults.
3) Oil pump rotor assembly selection
(1) Tip clearance
Install the inner rotor and outer rotor to oil pump
housing. With rotor gears facing each other,
measure the crest-to-crest clearance.
Tip clearance:
0.02 — 0.15 mm (0.0008 — 0.0059 in)
(2) Side clearance
Set a depth gauge to oil pump housing, then
measure the oil pump housing-to-rotor clear-
ance.
Side clearance:
0.02 — 0.045 mm (0.0008 — 0.0018 in)
(3) If the depth and/or side clearance are not
within the specification, replace the rotor as-
sembly.
Measure the total end play and adjust it to be
within specifications. <Ref. to 5AT-107, AD-
JUSTMENT, AT Main Case.>
(A) Thickness gauge
(B) Inner rotor
(C) Outer rotor
AT-01977
(A)
(B)
(C)
(A) Depth gauge
(B) Inner rotor
(C) Outer rotor
Oil pump rotor assembly
Part No.
Thickness mm (in)
15008AA130
11.37 — 11.38 (0.4476 — 0.4480)
15008AA140
11.38 — 11.39 (0.4480 — 0.4484)
15008AA150
11.39 — 11.40 (0.4484 — 0.4488)
AT-01978
(A)
(C)
(B)
5AT-87
Drive Pinion Shaft Assembly
AUTOMATIC TRANSMISSION
33.Drive Pinion Shaft Assembly
A: REMOVAL
1) Remove the transmission assembly from vehicle
body. <Ref. to 5AT-39, REMOVAL, Automatic
Transmission Assembly.>
2) Pull out the torque converter assembly. <Ref. to
5AT-67, REMOVAL, Torque Converter Assembly.>
3) Remove the transmission harness connector
from stay.
4) Disconnect the air breather hose. <Ref. to 5AT-
65, REMOVAL, Air Breather Hose.>
5) Remove the oil charge pipe. <Ref. to 5AT-66,
REMOVAL, Oil Charge Pipe.>
6) Remove the ATF inlet and outlet pipes. <Ref. to
5AT-62, REMOVAL, ATF Cooler Pipe and Hose.>
7) Separate the converter case and transmission
case. <Ref. to 5AT-81, REMOVAL, Converter
Case.>
8) Remove the drive pinion shaft mounting bolts,
and then remove the drive pinion shaft assembly
from oil pump cover.
9) Remove the oil pump cover from AT main case.
<Ref. to 5AT-83, Oil Pump Cover.>
B: INSTALLATION
1) Assemble the drive pinion assembly to oil pump
cover.
NOTE:
Be careful not to bend the shim.
Tightening torque:
70 N·m (7.1 kgf-m, 51.6 ft-lb)
2) Adjust the tooth contact between drive pinion
shaft assembly and the front differential side gear.
<Ref. to 5AT-90, ADJUSTMENT, Drive Pinion
Shaft Assembly.>
3) Join the converter case with the transmission
case. <Ref. to 5AT-81, INSTALLATION, Converter
Case.>
4) Install the transmission harness connector to the
stay.
5) Install the ATF cooler pipe. <Ref. to 5AT-63, IN-
STALLATION, ATF Cooler Pipe and Hose.>
6) Install the oil charge pipe with O-ring. <Ref. to
5AT-66, INSTALLATION, Oil Charge Pipe.>
7) Install the torque converter assembly. <Ref. to
5AT-67, INSTALLATION, Torque Converter As-
sembly.>
8) Install the transmission assembly to the vehicle.
<Ref. to 5AT-43, INSTALLATION, Automatic
Transmission Assembly.>
AT-01984
AT-01984
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст