Subaru Legacy III (2000-2003 year). Service manual — part 880
AC-56
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC) (LHD
MODEL)
D: DTC 25 OR –25 (SUNLOAD SENSOR)
TROUBLE SYMPTOM:
• Sensor identified that sunlight is at maximum. Then, A/C system is controlled to COOL side.
• Sensor identified that sunlight is at minimum. Then, A/C system is controlled to HOT side.
NOTE:
When the sunload sensor is checked inside the passenger compartment or in the shade, DTC “25” may ap-
pear on the indicator. Always check the sunload sensor in a place where it senses direct sunlight.
WIRING DIAGRAM:
AC-00324
i51
SUNLOAD
SENSOR
i51
1 2
i49
B:
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
i49
B:
i48
A:
AUTO A/C
CONTROL MODULE
B17
B16
1
2
AC-57
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC) (LHD
MODEL)
Step
Value
Yes
No
1
CHECK INPUT VOLTAGE TO SUNLOAD
SENSOR.
1) Turn ignition switch to OFF.
2) Remove sunload sensor. <Ref. to AC-48,
REMOVAL, Sunload Sensor (Auto A/C).>
3) Turn ignition switch to ON.
4) Measure input voltage to sunload sensor.
Connector & terminal
(i51) No. 2 (+) — No. 1 (
−−−−
):
Is the measured value the same as speci-
fied value?
Approx. 4.2 V
2
CHECK HARNESS CONNECTOR BETWEEN
A/C CONTROL MODULE AND SUNLOAD
SENSOR.
1) Turn ignition switch to OFF.
2) Disconnect connectors from A/C control
module.
3) Measure resistance of harness between A/
C control module and sunload sensor.
Connector & terminal
(i51) No. 2 — (i49) No. 16:
Is the measured value less than the speci-
fied value?
1
Ω
Repair harness
between A/C con-
trol module and
sunload sensor.
3
CHECK HARNESS CONNECTOR BETWEEN
A/C CONTROL MODULE AND SUNLOAD
SENSOR.
Measure resistance of harness between A/C
control module and sunload sensor.
Connector & terminal
(i51) No. 1 — (i49) No. 17:
Is the measured value less than the specified
value?
1
Ω
Repair harness
between A/C con-
trol module and
sunload sensor.
4
CHECK VOLTAGE OF INPUT SIGNAL TO A/
C CONTROL MODULE.
1) Connect connectors to A/C control module
and sunload sensor.
2) Turn ignition switch to ON.
3) Measure voltage between A/C control mod-
ule connectors.
Connector & terminal
(i49) No. 16 (+) — No. 17 (
−−−−
):
Is the measured value the same as speci-
fied value?
Approx. 2.5 V
Replace sunload
sensor.
5
CHECK POOR CONTACT.
Check poor contact in A/C control module con-
nector.
Is there poor contact in connector?
There is no poor contact.
Replace A/C con-
trol module.
Repair connector.
AC-58
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC) (LHD
MODEL)
E: DTC 31, 32, 33, 34 OR 35 (MODE DOOR ACTUATOR)
TROUBLE SYMPTOM:
Air flow outlet is not changed.
WIRING DIAGRAM:
AC-00372
B77
A:
i48
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
B77
i40
B201
4
7
1
2
10
8
9
5
6
A6
A5
A1
A2
A10
A9
1 2 3 4 5 6 7 8 9 10
A:
i48
B:
i49
AUTO A/C
CONTROL
MODULE
MODE ACTUATOR
6
5
3
1
2
4
i40
1 2
3 4
5
8
10
9
6 7
AC-59
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC) (LHD
MODEL)
Step
Value
Yes
No
1
CHECK POWER SUPPLY FOR AUTO A/C
CONTROL MODULE SIDE.
1) Turn the ignition switch to ON.
2) Press the mode switch to VENT position.
3) Press the DEF switch and measure the
voltage between auto A/C control module
and chassis ground when VENT is
changed to DEF position.
Connector & terminal
(i48) No. 6 (+) — Chassis ground (
−−−−
):
Is the measured value more than specified
value?
12 V
Replace the auto
A/C control mod-
ule.
2
CHECK POWER SUPPLY FOR ACTUATOR
SIDE.
1) Press the mode switch to VENT position.
2) Press the DEF switch and measure the
voltage between mode door actuator har-
ness connector and chassis ground when
VENT is changed to DEF position.
Connector & terminal
(B77) No. 2 (+) — Chassis ground (
−−−−
):
Is the measured value more than specified
value?
7 V (At normal temperature)
Repair the har-
ness between auto
A/C control mod-
ule and mode door
actuator.
3
CHECK POWER SUPPLY FOR AUTO A/C
CONTROL MODULE SIDE.
1) Press the DEF switch.
2) Press the mode switch to VENT position
and measure the voltage between auto A/C
control module and chassis ground when
DEF is changed to VENT position.
Connector & terminal
(i48) No. 5 (+) — Chassis ground (
−−−−
):
Is the measured value more than specified
value?
12 V
Replace the auto
A/C control mod-
ule.
4
CHECK POWER SUPPLY FOR ACTUATOR
SIDE.
1) Press the DEF switch.
2) Press the mode switch to VENT position
and measure the voltage between mode
door actuator harness connector and chas-
sis ground when DEF is changed to VENT
position.
Connector & terminal
(B77) No. 1 (+) — Chassis ground (
−−−−
):
Is the measured value more than specified
value?
7 V (At normal temperature)
Repair the har-
ness between auto
A/C control mod-
ule and mode door
actuator.
5
CHECK ACTUATOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from mode door
actuator.
3) Connect the battery positive (+) terminal to
terminal No. 1 and ground (
−
) terminal to
terminal No. 2 of mode door actuator to
make sure that actuator operates.
4) Connect the battery positive (+) terminal to
terminal No. 2 and ground (
−
) terminal to
terminal No. 1 of mode door actuator to
make sure that actuator operates.
Does the motor operate normally?
The motor operates normally.
Replace the mode
door actuator.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст