Subaru Legacy III (2000-2003 year). Service manual — part 920
LI-14
LIGHTING SYSTEM
COMBINATION BASE SWITCH ASSEMBLY
2. PARKING SWITCH
Measure parking switch resistance.
Switch position
Terminal No.
Standard
OFF
2 and 4
Less than 1
Ω
ON
1 and 4
Less than 1
Ω
1
2
3
4
LI-00183
LI-15
LIGHTING SYSTEM
HEADLIGHT ASSEMBLY
12.Headlight Assembly
A: REMOVAL
1) Disconnect ground cable from battery.
2) Remove duct (A) (when right side headlight is re-
moved).
3) Disconnect headlight bulb connector.
4) Remove three bolts and disconnect connectors,
and then detach headlight assembly.
B: INSTALLATION
Install in the reverse order of removal.
LI-00073
( A )
LI-00129
LI-00130
LI-16
LIGHTING SYSTEM
HEADLIGHT ASSEMBLY
C: ADJUSTMENT
1. HEADLIGHT AIMING
CAUTION:
Turn off the light before adjusting headlight
aiming. If the light is necessary to check aim-
ing, do not turn on for more than two minutes.
NOTE:
Before checking the headlight aiming, be sure of
the following:
• The area around the headlight has not sustained
any accident, damage or other type of deformation.
• Vehicle is parked on level ground.
• The inflation pressure of tires is correct.
• Vehicle's gas tank is fully charged.
• Bounce the vehicle several times to normalize
the suspension.
• Make certain that someone is seated in the driv-
er's seat.
Turn the headlights on and then adjust the low
beam pattern to the following positions on the
screen.
NOTE:
• Set the headlight leveler switch to “0” position.
• Adjust vertical aim (A) first, then horizontal aim
(B).
This illustration is for LHD model.
The pattern for RHD model is symmetrically opposite.
LI-00131
( A )
( B )
(A) Vehicle center
(B) Bulb center
W mm (in)
H mm (in)
h mm (in) at 3 m (10 ft)
Sedan
Wagon
Outback
Conventional sus-
pension
Air suspension
1,130 (44.69)
665 (26.18)
660 (25.98)
650 (25.59)
725 (28.54)
30 (1.18)
LI-00132
W1
W1
W
W
H
H
3 m (10 ft)
H
W2
W2
h
h
( A )
( A )
( B )
LI-17
LIGHTING SYSTEM
HEADLIGHT BULB
13.Headlight Bulb
A: REMOVAL
CAUTION:
• Because the tungsten halogen bulb operates
at a high temperature, dirt and oil on the bulb
surface reduces the bulb's service life. Hold the
flange portion when replacing the bulb. Never
touch the glass portion.
• Do not leave the headlight without a bulb for
a long time. Dust, moisture, etc. entering the
headlight may affect its the performance.
1) Disconnect ground cable from battery.
2) Remove duct (A) (when right side headlight is re-
moved).
3) Remove back cover (A).
4) Disconnect harness connector.
5) Push to remove spring retainer and then detach
headlight bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATIONS, General Description.>
3) If NG, replace the bulb with a new one.
LI-00073
( A )
LI-00134
( A )
LI-00135
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст