Subaru BRZ (2012 year). Service manual — part 16
PI-11
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
NOTE:
• The hazard lights flash twice and the buzzer
sounds twice when unlocking.
• The hazard lights flash once and the buzzer
sounds once when locking.
• While carrying the access key, check that the
trunk unlocks when you press the trunk opener but-
ton.
• Close all doors, and while carrying the access
key, check that all doors are locked automatically
30 seconds after grasping the front door knob
(touching the touch sensor) to unlock doors.
• Check the mechanical key attached to the ac-
cess key can be used for locking/unlocking.
• With the access key in the vehicle, check that
warning buzzer sounds and locking does not occur
when you touch the door touch sensor.
CAUTION:
Remove the mechanical key from the access
key and hold the mechanical key.
• With the front door locked and the access key in
the trunk (with trunk closed), check that the warning
buzzer sounds and the trunk unlocks when you
press the trunk opener button.
22.SECURITY SYSTEM
• Model with keyless access function
Check that the security system operates as indicat-
ed below.
1) Turn on the security system.
2) Fully open all the door windows.
3) Remove the key from ignition switch, and then
close all doors.
4) Press the access key “LOCK” button once.
5) When all doors are locked, the security indicator
light illuminates to indicate that the alarm system is
in the monitoring prepared condition.
6) The security indicator light flashes once for two
seconds 30 seconds after the condition of step 5) is
reached, and the system enters the monitoring
condition.
(A) Lock-touch sensor
(A) Trunk opener button
(A) Mechanical key
PI-00785
(A)
PI-00771
(A)
PI-00786
(A)
(1) Security indicator light
PI-00813
PI-00773
(1)
PI-12
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
7) Press the access key “UNLOCK” button once.
8) The driver’s door unlocks and the alarm system
is in the non-monitoring condition.
9) Check that the alarm does not sound when any
of the doors are opened.
10) Press the access key “LOCK” button once with
one door open.
11) Check that the buzzer sounds to warn that the
door is not fully closed.
12) Close all doors.
13) Illuminates to indicate monitoring prepared
condition (indicator light illuminates).
14) The security indicator light flashes once for two
seconds 30 seconds after the condition of step 13)
is reached, and the system enters the monitoring
condition.
15) Press the “UNLOCK” button on the access key
once to turn the system into non-monitoring condi-
tion.
16) Momentarily press the “LOCK” button of the
power door lock switch with any one door open.
• Driver’s side
• Passenger’s side
17) Close all doors.
18) When all doors are locked, the indicator light il-
luminates to indicate that the alarm system is in the
monitoring prepared condition.
19) The security indicator light flashes once for two
seconds 30 seconds after the condition of step 18)
is reached, and the system enters the monitoring
condition.
20) When the alarm system is in the monitoring
condition, use the inner lock knob or the key to un-
lock the door.
21) Check that the alarm condition occurs (horn
sounds continuously, hazard light flashes, security
indicator illuminates).
22) Check that the condition described in 21) con-
tinues for 60 seconds or more, or until the access
key “UNLOCK” button is pressed, or until the posi-
tion switch is turned ON with the correct access
key.
23) When none of above is applicable, perform
troubleshooting for the security system.
24) Turn off the security system.
PI-00814
PI-00813
PI-00814
PI-00776
PI-00779
PI-13
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
23.SEAT
1) Check that each seat provides full functionality in
sliding and reclining. Check all available functions
of the rear seat such as the backrest tilt knob.
2) Check the passenger’s seat occupant detection
system.
(1) Empty the passenger’s seat and turn the ig-
nition switch to ON.
(2) Check that the passenger airbag ON/OFF
indicator lights both turn on simultaneously for
approximately six seconds, and after turning off
for two seconds, only the OFF light illuminates.
3) Have an adult passenger sit in the passenger’s
seat, and check whether the ON light of the pas-
senger side airbag ON/OFF indicator illuminates.
4) Have the passenger get out of the passenger’s
seat, and check whether the OFF light of the pas-
senger side airbag ON/OFF indicator illuminates.
24.SEAT BELT
1) Pull out the seat belt and then release it. Check
that the belt retracts smoothly.
2) Check seat belt warning function
(1) Turn the ignition switch to ON with the driv-
er’s and passenger’s seat belt detached.
(2) Check the driver’s and passenger’s seat belt
warning light blink for approx. 6 seconds and
the buzzer sounds intermittently.
(3) Afterwards, check that the seat belt warning
lights illuminate. (If no passenger is on the pas-
senger’s seat, the seat belt warning light on
passenger’s seat does not operate.)
25.TPMS (U.S. MODEL)
1) Turn the ignition switch to ON, and check that
the TPMS warning light is in a normal operation
condition.
• Normal operation (IG ON (Light check))
2) If the TPMS warning light display does not oper-
ate normally, check and repair the system.
26.GROMMET INSTALLATION
Install the grommet contained in the glove box to
the tie-down hole.
CAUTION:
Securely install the grommet to ensure that the
tie-down hole is blocked up by the grommet.
Dust or foul odors could pass into the side seal
through the tie-down hole and enter the interior
directly from the rear quarter.
27.HORN
Check if the horn sounds.
28.HAZARD LIGHT
Check that the hazard lights illuminate.
29.MAP LIGHT
After installing the fuse, check that the map light il-
luminates/turns off normally.
PI-00787
(1) Grommet
2s
IGN ON
ON
OFF
PI-00376
(1)
PI-00801
PI-14
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
30.DELIVERY MODE CONNECTOR
Connect the delivery mode connector of the driv-
er's side A pillar lower area. After connection,
check that the key interlock system functions.
31.IMMOBILIZER SYSTEM
1) Check that the engine starts with all keys that are
equipped on vehicle. Also, when starting the en-
gine, check that the security indicator light goes off.
2) Check that the security indicator light flashes im-
mediately after removing the key. (model without
keyless access function)
3) Check that the security indicator light flashes im-
mediately after turning the ignition switch from ON
to ACC or OFF, or when the doors are opened/
closed with the ignition switch at ON or ACC. (mod-
el with keyless access function)
NOTE:
If malfunctions occur, refer to “IMMOBILIZER (DI-
AGNOSIS)”.
32.STARTING CONDITION
Start the engine and check that the engine starts
smoothly. If the battery voltage is low, recharge or
replace the battery. If any noises are observed, im-
mediately stop the engine and check and repair the
abnormal components.
33.EXHAUST
Listen to the exhaust noise to see if no noises are
observed. Check that no leaks are found.
34.INDICATOR AND WARNING LIGHTS
Check that all indicator lights and warning lights are
operating correctly.
35.HEATER & VENTILATION
Operate the heater & ventilation system to check
for normal airflow outlet control, air inlet control, air-
flow capacity and heating performance.
36.AIR CONDITIONER
Operate the air conditioner. Check that the A/C
compressor operates normally and enough cooling
is provided.
NOTE:
To prevent the insufficient lubrication of the air con-
ditioner, operate the air conditioner for five minutes
at idling.
37.CLOCK
Check that the clock operates normally.
38.AUDIO
1) Check if the AM/FM radio broadcasting can be
heard.
2) Check that all the radio functions work properly
and the noise level is normal.
3) Check the CD and AUX for normal operation.
4) Check that the AUX is installed into the console
without looseness.
39.NAVIGATION SYSTEM
1) Check all display functions for normal operation.
(Refer to the operation manual.)
2) Check that the navigation system operates nor-
mally.
3) Check the radio, CD player and AUX for normal
operation.
4) Check that the AUX is installed into the console
without looseness.
40.ACCESSORY POWER SUPPLY SOCKET
1) Check operation of the accessory power supply
socket in console box.
2) Check operation of the accessory power supply
socket in the glove box.
41.LIGHTING
1) Check the headlight operations. When pulling
out the key, check if the headlight illuminates by
turning the headlight switch from OFF to ON.
2) Check the stop light operation.
3) Check other lights for normal operations.
42.VSC
• With the engine running, operate the VSC
SPORT switch, and check that the “VSC SPORT”
and “VSC OFF” indicator lights illuminate and that
they turn off when the switch is operated again.
• With the engine running, press the VSC OFF
switch for a short period (approx. 1 sec. or less),
and check that the “TRC OFF” indicator light illumi-
nates and that it turns off when the switch is oper-
ated again.
• With the engine running, press the VSC OFF
switch for a long period (approx. 3 sec. or more),
and check that the “TRC OFF” and “VSC OFF” in-
dicator lights illuminate and that they turn off when
the switch is pressed again for a short period.
(A) Delivery mode connector
(A)
PI-00795
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст