Subaru BRZ (2012 year). Service manual — part 14
PI-3
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
Checks with the engine running
13. Engine oil
Check the engine oil amount.
14. Transmission gear oil
Check for leakage of the transmission gear oil.
15. Rear differential gear oil
Check for leakage of gear oil from the rear differential.
16. Engine coolant
Check the engine coolant level.
17. Clutch fluid
Check the clutch fluid amount.
18. Window washer fluid
Check the window washer fluid amount.
19. Front hood latch
Check that the front hood is closed normally and locked securely.
20. Keyless entry system
Check that the keyless entry system operates normally.
21. Keyless access function
Check that the keyless access function operates normally.
22. Security system
Check that the security system operates normally.
23. Seat
1. Check the seat surfaces for stains or dirt.
2. Check the seat installation conditions and functionality.
24. Seat belt
Check the seat belt installation conditions and functionality.
25. TPMS (U.S. model)
Check that the TPMS warning light operates normally. If it does not operate
normally, perform the diagnosis by referring to TPMS (Diagnosis).
26. Grommet installation
Install the grommet contained in the glove box to the tie-down hole.
27. Horn
Check if the horn sounds.
28. Hazard lights
Check that the hazard lights illuminate.
29. Map light
After installing the fuse, check that the map light illuminates/turns off nor-
mally.
Step
Check point
30. Delivery mode connector
Install the delivery mode connector.
31. Immobilizer system
1. Check that the engine starts with all keys that are equipped on vehicle.
2. Check that the security indicator light flashes immediately after removing
the key.
32. Starting condition
Start the engine and check that the engine starts smoothly.
33. Exhaust system
Check that the exhaust noise is normal and no leaks are found.
34. Indicator and warning lights
Check that all indicator lights and warning lights are operating correctly.
35. Heater & ventilation
Check that the heater & ventilation system operates normally.
36. Air conditioner
Check that the air conditioner operates normally.
37. Clock
Check that the clock operates normally.
38. Audio
Check the radio and AUX operate normally.
39. Navigation
Check the navigation and AUX operate normally.
40. Accessory power supply socket
Check that the accessory power supply socket operates normally.
41. Lighting system
Check that the lighting system operates normally.
42. Vehicle stability control (VSC)
Check the VSC SPORT and VSC OFF switch functions for normal operation.
43. Illumination control
Check that the illumination control operates normally.
44. Window washer
Check that the window washer system operates normally.
45. Wiper
Check that the wiper system operates normally.
46. Power window
Check that the power window operates normally.
47. Rear defogger
Check that the rear defogger operates normally.
48. Door mirror
Check that the remote control mirror and heated mirror operate normally.
49. Diagnostic trouble code (DTC) check
Check that the diagnostic trouble code (DTC) is not detected.
Step
Check point
PI-4
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
Dynamic Test with the Vehicle Running
Checks after Dynamic Test
1. APPEARANCE
• If the vehicle is covered with protective coating,
visually check the vehicle body for damage and
dents.
• When there is no protective coating, check the
body paints for damage or stains in detail and re-
pair as necessary.
• Check the window glass, door glass, and lights
for any cracks or damage, and replace as neces-
sary.
• Visually check the plated parts, such as the
grilles and door knobs, for damage or loss of gloss
and replace the parts as necessary.
• Check the instrument panel, console and trim for
stains or dirt.
2. TIRE
• Check the tires for damage, defective, and dents
on wheels.
• Check the tire size, spare tire and tire air pres-
sure described on the tire air pressure label (driv-
er’s side).
3. FUSE INSTALLATION
The DCC (back-up) 30A fuse is moved from posi-
tion (A) to (B) as shown in the figure below to pre-
vent battery consumption when vehicles are
delivered. Remove the fuse from (B) and install in
(A) as shown in the figure below.
Step
Check point
50. Brake test
Check the foot brake for normal operations.
51. Parking brake
Check the parking brake for normal operations.
52. Shift control
Check that the shift patterns are correct.
53. Cruise control
Check that the cruise control system operates normally.
Step
Check point
54. Fluid leakage
Check for fluid/oil leaks.
55. Water leak test
Spray the vehicle with water and check for water leaks.
56. Appearance 2
1. Remove the protective coating (if equipped).
2. Check the body paints for damage and stain.
3. Check the plated parts for damage and rust.
(A)
(B)
NT-00457
PI-5
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
4. LOCK/UNLOCK AND OPEN/CLOSE OP-
ERATION CHECKS OF DOORS
1) Using the key, lock and unlock the door several
times to check for normal operation. Open and
close the door several times for smooth movement.
2) Completely close the driver’s door, and then
check the smooth movement with operating door
lock knob from lock to unlock several times. Set the
door lock knob (A) to lock position. Then pull the in-
ner remote (B) to ensure that doors will not open.
For other doors, place the door lock knob (A) to lock
position and then pull the inner remote (B) to en-
sure that doors will not open.
3) Close all the doors, and then press the lock on
power door lock switch at driver’s side. Check that
all doors lock.
4) Press the driver’s side power door lock switch to
unlock side. Check that all doors unlock.
5) Check that the passenger’s power door lock
switch locks and unlocks normally in the same
manner.
6) Insert the key to ignition switch, and open the
driver’s side door. Press lock on power door lock.
Check that the door is not locked.
5. TRUNK LID OPEN/CLOSE OPERATIONS
1) Operate the trunk lock release lever to check
that the trunk lid opens.
2) Open and close the trunk lid several times for
smooth movement.
3) Press the trunk opener lock button in the trunk.
4) Check that the trunk lid will not open even when
the trunk opener button is pressed.
(A) Door lock knob
(B) Inner remote
PI-00604
PI-00688
(A)
(B)
PI-00776
(A) Lock
(B) Unlock
PI-00777
PI-00778
(A)
(B)
PI-00790
PI-6
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
6. OPERATION CHECK OF TRUNK LID RE-
LEASE HANDLE
CAUTION:
Do not check the trunk lid release handle when
in the trunk. If the trunk lid release handle is de-
fective, you may be trapped in.
1) Use a flat tip screwdriver. Slide the screwdriver
blade from the slit aperture of the lock assembly ful-
ly to the end until you hear a click. This places the
latch in the locked position.
2) Make sure the latch is released by pulling the
yellow trunk lid release handle in the direction of ar-
row.
7. FUEL LID OPENER LEVER
Operate the fuel lid opener lever to check that the
fuel lid is unlocked normally. Check that the filler
cap is securely closed.
8. TOWING HOOK (EYEBOLT)
NOTE:
At factory shipment, the towing hook (eyebolt) is in-
stalled to the rear bumper for securing the vehicle
during transportation. Follow the procedure below
to store the towing hook (eyebolt) to the holder in
the spare tire.
1) Remove the towing hook (eyebolt) from the rear
bumper.
2) Store the towing hook (eyebolt) to the holder in
the trunk. (Clean any dirt that is present.)
3) Install the supplied rear hook cover to rear
bumper.
PI-00248
PI-00693
(A) Towing hook (eyebolt)
(A) Towing hook (eyebolt)
(B) Jack
PI-00753
(A)
(A)
(B)
PI-00755
PI-00754
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст