Infiniti M35/M45 Y50. Manual — part 829
REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-113
C
D
E
F
G
H
J
K
L
M
A
B
GW
3.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1.
Connect automatic drive positioner control unit connector.
2.
Turn ignition switch ON.
3.
[Door mirror LH]
Check voltage between automatic drive positioner control unit connector and ground.
4.
[Door mirror RH]
Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK
>> Replace malfunction door mirror actuator.
NG
>> Replace automatic drive positioner control unit.
Terminals
Mirror switch condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic
drive posi-
tioner con-
trol unit
connector
Terminal
M6
16
Ground
DOWN / RIGHT
Battery voltage
Other than above
0
31
UP
Battery voltage
Other than above
0
32
LEFT
Battery voltage
Other than above
0
Terminals
Mirror switch condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic
drive posi-
tioner con-
trol unit
connector
Terminal
M6
14
Ground
UP
Battery voltage
Other than above
0
15
LEFT
Battery voltage
Other than above
0
30
DOWN / RIGHT
Battery voltage
Other than above
0
PIIB6025E
PIIB6026E
GW-114
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Check Mirror Sensor Circuit
NIS0023E
1.
CHECK MIRROR SENSOR INSPECTION
With CONSULT-II
Check the voltage on (MIR/SE LH R–L, MIR/SE LH U–D, MIR/SE RH R–L, MIR/SE RH U–D) in the DATA
MONITOR.
Without CONSULT-II
1.
Turn ignition switch ON.
2.
Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK
>> Mirror sensor LH circuit is OK.
NG
>> GO TO 3.
2.
CHECK MIRROR SENSOR POWER SUPPLY 1
Check voltage between door mirror connector and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 3.
Monitor item
[OPERATION or UNIT]
Contents
MIR/SE LH R–L
“V”
Voltage output from door mirror LH horizontal sensor
(LH/RH) is displayed.
MIR/SE LH U–D
“V”
Voltage output from door mirror LH vertical sensor
(UP/DOWN) is displayed.
MIR/SE RH R–L
“V”
Voltage output from door mirror RH horizontal sensor
(LH/RH) is displayed.
MIR/SE RH U–D
“V”
Voltage output from door mirror RH vertical sensor
(UP/DOWN) is displayed.
PIIA0197E
Terminals
Mirror face position
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner control
unit connector
Terminal
M6
Door
mirror
RH side
5
Ground
Close to perk
4.2
Close to valley
0.5
21
Close to left edge
3.5
Close to right edge
0.5
Door
mirror
LH side
6
Close to perk
4.2
Close to valley
0.5
22
Close to left edge
0.5
Close to right edge
3.5
PIIB6027E
Terminals
Voltage (V)
(Approx.)
(+)
(-)
Door mirror
connector
Terminal
D2 (LH)
D39 (RH)
11
Ground
Battery voltage
PIIB6032E
REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-115
C
D
E
F
G
H
J
K
L
M
A
B
GW
3.
CHECK MIRROR SENSOR POWER SUPPLY 2
1.
Turn ignition switch OFF.
2.
Disconnect door mirror connector.
3.
Turn ignition switch ON.
4.
Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Replace automatic drive positioner control unit.
4.
CHECK HARNESS CONTINUITY 1
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit connector and door mirror connector.
4.
Check continuity between automatic drive positioner control unit
connector and ground.
OK or NG
OK
>> Check the condition of harness and connector.
NG
>> Repair or replace harness.
Terminals
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner control
unit connector
Terminal
M7
33
Ground
Battery voltage
PIIB6028E
A
B
Continuity
Automatic
drive posi-
tioner control
unit connector
Terminal
Door mirror
connector
Terminal
M7
33
D2 (LH)
D39 (RH)
11
Yes
A
Ground
Continuity
Automatic drive
positioner control
unit connector
Terminal
M7
33
No
PIIB6033E
GW-116
REVERSE INTERLOCK DOOR MIRROR SYSTEM
5.
CHECK MIRROR SENSOR GROUND 1
1.
Turn ignition switch OFF.
2.
Disconnect door mirror connector.
3.
Check continuity between door mirror connector and ground.
OK or NG
OK
>> GO TO 8.
NG
>> GO TO 6.
6.
CHECK MIRROR SENSOR GROUND 2
Check continuity between automatic drive positioner control unit connector and ground.
OK or NG
OK
>> GO TO 7.
NG
>> Replace auto drive positioner control unit.
7.
CHECK HARNESS CONTINUITY 2
1.
Disconnect automatic drive positioner control unit connector.
2.
Check continuity between automatic drive positioner control unit connector and door mirror connector.
3.
Check continuity between automatic drive positioner control unit
connector and door mirror connector.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Repair or replace harness between automatic drive positioner control unit and door mirror.
Door mirror connector
Terminal
Ground
Continuity
D2 (LH)
D39 (RH)
12
Yes
PIIB6034E
Automatic drive posi-
tioner control unit con-
nector
Terminal
Ground
Continuity
M7
41
Yes
PIIB6029E
A
B
Continuity
Automatic
drive posi-
tioner control
unit connector
Terminal
Door mirror
connector
Terminal
M7
41
D2 (LH)
D39 (RH)
12
Yes
A
Ground
Continuity
Automatic drive
positioner control
unit connector
Terminal
M7
41
Yes
PIIB6035E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст