Infiniti M35/M45 Y50. Manual — part 426
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER
EC-177
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER
PFP:226A0
Description
NBS004U8
SYSTEM DESCRIPTION
The ECM performs ON/OFF control of the heated oxygen sensor 2 heater corresponding to the engine speed,
amount of intake air and engine coolant temperature.
OPERATION
CONSULT-II Reference Value in Data Monitor Mode
NBS004U9
Specification data are reference values.
On Board Diagnosis Logic
NBS004UA
Sensor
Input signal to ECM
ECM function
Actuator
Camshaft position sensor (PHASE)
Crankshaft position sensor (POS)
Engine speed
Heated oxygen sensor 2
heater control
Heated oxygen sensor 2 heater
Engine coolant temperature sensor
Engine coolant temperature
Mass air flow sensor
Amount of intake air
Engine speed rpm
Heated oxygen sensor 2 heater
Above 3,600
OFF
Below 3,600 rpm after the following conditions are met.
●
Engine: After warming up
●
Keeping the engine speed between 3,500 and 4,000 rpm for 1
minute and at idle for 1 minute under no load
ON
MONITOR ITEM
CONDITION
SPECIFICATION
HO2S2 HTR (B1)
HO2S2 HTR (B2)
●
Engine speed: Below 3,600 rpm after the following conditions are met.
–
Engine: After warming up
–
Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load
ON
●
Engine speed: Above 3,600 rpm
OFF
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P0037
0037
(Bank 1)
Heated oxygen
sensor 2 heater
control circuit low
The current amperage in the heated oxygen sen-
sor 2 heater circuit is out of the normal range.
(An excessively low voltage signal is sent to ECM
through the heated oxygen sensor 2 heater.)
●
Harness or connectors
(The heated oxygen sensor 2 heater circuit is
open or shorted.)
●
Heated oxygen sensor 2 heater
P0057
0057
(Bank 2)
P0038
0038
(Bank 1)
Heated oxygen
sensor 2 heater
control circuit high
The current amperage in the heated oxygen sen-
sor 2 heater circuit is out of the normal range.
(An excessively high voltage signal is sent to
ECM through the heated oxygen sensor 2
heater.)
●
Harness or connectors
(The heated oxygen sensor 2 heater circuit is
shorted.)
●
Heated oxygen sensor 2 heater
P0058
0058
(Bank 2)
EC-178
[VQ35DE]
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER
DTC Confirmation Procedure
NBS004UB
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is between 11V and 16V at
idle.
WITH CONSULT-II
1.
Turn ignition switch ON and select “DATA MONITOR” mode with
CONSULT-II.
2.
Start engine and warm it up to the normal operating tempera-
ture.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Start the engine and keep the engine speed between 3,500 rpm
and 4,000 rpm for at least 1 minute under no load.
5.
Let engine idle for 1 minute.
6.
If 1st trip DTC is detected, go to
EC-182, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF174Y
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER
EC-179
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
NBS004UC
BANK 1
TBWT1470E
EC-180
[VQ35DE]
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
25
P/B
Heated oxygen sensor 2
heater (bank 1)
[Engine is running]
●
Engine speed: Below 3,600 rpm after the
following conditions are met
–
Engine: After warming up
–
Keeping the engine speed between 3,500
and 4,000 rpm for 1 minute and at idle for 1
minute under no load
0 - 1.0V
[Ignition switch: ON]
●
Engine stopped
[Engine is running]
●
Engine speed: Above 3,600 rpm
BATTERY VOLTAGE
(11 - 14V)
74
W
Heated oxygen sensor 2
(bank 1)
[Engine is running]
●
Revving engine from idle to 3,000 rpm
quickly after the following conditions are met
–
Engine: After warming up
–
Keeping the engine speed between 3,500
and 4,000 rpm for 1 minute and at idle for 1
minute under no load
0 - Approximately 1.0V
78
B
Sensor ground
(Heated oxygen sensor)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 0V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст