Infiniti M35/M45 Y50. Manual — part 925
![](/vehicles/zatt/cen/houeebante/friet.png)
BACK-UP LAMP
LT-245
C
D
E
F
G
H
I
J
L
M
A
B
LT
BACK-UP LAMP
PFP:26550
Wiring Diagram — B/LAMP —
NKS003SE
TKWT5069E
![](/vehicles/zatt/cen/houeebante/ythinopesu.png)
LT-246
BACK-UP LAMP
Bulb Replacement
NKS003SF
1.
Remove trunk lid finisher inner. Refer to
2.
Turn bulb socket (1) counterclockwise and unlock it.
3.
Remove bulb (2) from its socket.
Back-up lamp
: 12V-18W
SKIB4189E
![](/vehicles/zatt/cen/houeebante/dach.png)
BACK-UP LAMP
LT-247
C
D
E
F
G
H
I
J
L
M
A
B
LT
Removal and Installation
NKS003SG
REMOVAL
1.
Remove trunk lid finisher inner. Refer to
2.
Disconnect back up lamp and trunk lid request switch connector.
3.
Remove trunk lid finisher outer. Refer to
4.
Remove screws and clip, and then remove back up lamp.
5.
Remove seal packing from back up lamp.
INSTALLATION
Installation is the reverse order of removal.
Install a new seal packing to the back up lamp.
CAUTION:
Seal packing cannot be reused.
1.
Nut
2.
Nut
3.
Seal packing
4.
Clip
5.
Back up lamp
6.
Two-sided tape
7.
Trunk lid finisher outer
8.
Screw
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
SKIB4190E
Back up lamp mounting nut
: 3.0 N·m (0.31 kg-m, 27 in-lb)
Trunk lid finisher mounting nut
: 3.0 N·m (0.31 kg-m, 27 in-lb)
![](/vehicles/zatt/cen/houeebante/gowinemes.png)
LT-248
PARKING, LICENSE PLATE AND TAIL LAMPS
PARKING, LICENSE PLATE AND TAIL LAMPS
PFP:26550
Component Parts and Harness Connector Location
NKS003SH
System Description
NKS003SI
The control of the parking, license plate and tail lamp operation is dependent upon the position of the lighting
switch (combination switch). When the lighting switch is placed in the 1ST position, the BCM (body control
module) receives input signal requesting the parking, license plate and tail lamps to illuminate. This input sig-
nal is communicated to the IPDM E/R (intelligent power distribution module engine room) across the CAN
communication lines. The CPU (central processing unit) located in the IPDM E/R controls the tail lamp relay
coil. This relay, when energized, directs power to parking, license plate and tail lamps, which then illuminate.
OUTLINE
Power is supplied at all times
●
through 15A fuse (No. 71, located in IPDM E/R)
●
to CPU located in IPDM E/R, and
●
to tail lamp relay located in IPDM E/R,
●
through 15A fuse (No. 78, located in IPDM E/R)
●
to CPU located in IPDM E/R,
●
through 50A fusible link (letter F, located in fuse, fusible link and relay block)
●
to BCM terminal 55,
●
through 10A fuse [No. 21, located in fuse block (J/B)]
●
to BCM terminal 42,
●
through 10A fuse [No. 22, located in fuse block (J/B)]
●
to key slot terminal 1.
PKID0503E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст