Mitsubishi Lancer Evolution IX. Manual — part 367

DOOR

BODY

42-29

REMOVAL SERVICE POINTS
<<A>> WINDOW REGULATOR ASSEM-
BLY/POWER WINDOW MOTOR ASSEM-
BLY REMOVAL

1. Remove the door window glass installation bolts.

CAUTION

If film or others are adhered to the door window
glass, attach special tool window glass holder
(MB990480) to the outside of the glass to prevent
the film from peeling off.

AC100009AB

MB990480

2. Lift the door window glass, and attach special tool

window glass holder (MB990480) to the glass as
shown to prevent the glass from falling.

3. Remove the window regulator assembly and

power window motor assembly

<<B>> CENTRE SASH UPPER REMOVAL

AC000602

Door outer

opening

weatherstrip

Door centre

sash

AB

1. Remove the door outer opening weatherstrip from

the centre sash upper only.

2. Remove the centre sash upper mounting screws,

and then remove the centre sash upper from the
door panel.

INSTALLATION SERVICE POINTS
>>A<< CENTRE SASH UPPER INSTALLA-
TION

Securely insert the centre sash upper into the win-
dow rear sash (door).

>>B<< POWER WINDOW MOTOR
ASSEMBLY INSTALLATION/WINDOW
REGULATOR ASSEMBLY

Y1536AU

Y1476AU

AC100010AB

<FRONT DOOR>

<REAR DOOR>

1

2

3

4

5

6

7

1

2

3

4

5

6

When installing the window regulator assembly,
tighten the bolts in the order shown in the illustration.

INSPECTION

M1429001400282

How to make the power window switch learn the
fully closed position of the power window
How to make the power window switch learn the
fully closed position when the power window
switch is removed, or the power window regula-
tor assembly is removed or replaced
1. If the anti-trap function (safety mechanism) is

activated consecutively three times or more, the
fully closed position that the power window switch
has learned will be erased (initialised).

2. Operate the power window switch and fully open

the door window glass.

DOOR

BODY

42-30

CAUTION

The anti-trap function does not work until the
power window switch completes learning the
fully closed position (It is because the anti-trap
function is reset).
3. Operate the power window switch and fully close

the door window glass. The power window
activates for 0.7 seconds and stops automatically
when the power window switch is pressed once.
Repeat this operation until the door window glass
fully closes and release the switch once. Then,
hold the power window switch to the fully closed
side again for one second so that the power
window switch completes learning the fully closed
position.
NOTE: If the power window switch is operated to
open the door window glass while the switch is
learning, learning will be cancelled. If this hap-
pens, return to step 2.

How to make the power window switch learn the
fully closed position when the power window
switch is replaced with a new one

CAUTION

The anti-trap function does not work until the
power window switch completes learning the
fully closed position (It is because the anti-trap
function is reset).
Operate the power window main switch to fully close
the door window glass by one-shot up action so that
the power window switch will complete learning (Ini-
tialisation is not needed).
NOTE: When the power window sub switch of each
seat is replaced, operate the power window main
switch to fully close the applicable power window by
one-shot up action (It is because the power window
sub switch does not have one-shot up/down func-
tion).

DOOR HANDLE AND LATCH

REMOVAL AND INSTALLATION

M1423004600458

Pre-removal Operation
• Door Trim Removal (Refer to GROUP 52A, Door trim

P.52A-12

).

Post-installation Operation
• Door Inside Handle Play Check (Refer to

P.42-25

).

• Door Outside Handle Play Check (Refer to

P.42-25

).

• Door Trim Installation (Refer to GROUP 52A, Door trim

P.52A-12

).

AC300270

1

2

3

4

5

6

8

9

1

2

4

5

7

8

9

<FRONT DOOR>

<REAR DOOR>

N

N

5.0 ± 1.0 N·m

9.0 ± 2.0 N·m

9.0 ± 2.0 N·m

5.0 ± 1.0 N·m

AB

Door handle and door latch assembly
removal steps

>>

C

<< 1. Door inside handle

•

Waterproof film (Refer to

P.42-33

).

2. Door outside handle
3. Door lock key cylinder

>>

B

<< 4. Lower sash

5. Door latch assembly
6. Inside lock cable (Front door)
7. Inside lock rod (Rear door)
8. Inside handle rod
Door check removal steps
•

Waterproof film (Refer to

P.42-33

).

>>

A

<< 9. Door check

DOOR

BODY

42-31

INSTALLATION SERVICE POINTS
>>A<< DOOR CHECK INSTALLATION

ACX00541

Identification mark

AB

Install the door check so that the identification mark
faces upwards.

Item

Identification
mark

Front Door

Left door

39L

Right door

39R

Rear Door

Left door

40L

Right door

40R

>>B<< LOWER SASH INSTALLATION

Securely insert the rear lower sash into the window
rear sash.

>>C<< DOOR INSIDE HANDLE
INSTALLATION

AC100404 AB

Clip

Inner cable

Outer cable end

Inside handle rod

Door inside handle

1. Install the inside lock cable to the door inside

handle as follows:
(1) Install the inner cable end in the inside lock

cable to the clip in the door inside handle.

(2) Turn the inside lock knob to the door lock

position.

(3) Install the outer cable end to the door inside

handle securely.

(4) Install the clip to the inner cable.

2. Install the inside handle rod to the door inside

handle.

3. Install the door inside handle to the door.

INSPECTION

M1423004700541

FRONT DOOR LOCK ACTUATOR CHECK

4

2
5

3
6

1

4

2
5

3
6

1

AC305111

B

A

AB

Lock

Unlock

View A

View B

Unlock

Lock

Front door <Left side>

<Right side>

Lever

Lever

Door handle and door latch assembly
removal steps (Continued)

DOOR

BODY

42-32

ACTUATOR OPERATION CHECK

Lever
position

Battery connection Lever

operation

At the
"LOCK"
position

• Connect terminal

No.4 and the
negative battery
terminal.

• Connect terminal

No.6 and the
positive battery
terminal.

The lever
moves from the
"LOCK"
position to the
"UNLOCK"
position.

At the
"UNLOCK"
position

• Connect terminal

No.6 and the
negative battery
terminal.

• Connect terminal

No.4 and the
positive battery
terminal.

The lever
moves from the
"UNLOCK"
position to the
"LOCK"
position.

ACTUATOR SWITCH CHECK <LH DRIVE VEHI-
CLES (DRIVER’S SIDE)>

Lever position

Tester
connection

Specified
condition

At the "LOCK"
position

1

− 2

Less than 2
ohms

At the "UNLOCK"
position

1

− 3

Less than 2
ohms

ACTUATOR SWITCH CHECK <RH DRIVE VEHI-
CLES (DRIVER’S SIDE)>

Lever position

Tester
connection

Specified
condition

At the "LOCK"
position

2

− 3

Less than 2
ohms

At the "UNLOCK"
position

1

− 3

Less than 2
ohms

REAR DOOR LOCK ACTUATOR CHECK

2 3

4

1

5 6

2 3

4

1

5 6

AC305112

B

A

AB

Rear door

Lock

Unlock

View A

View B

Unlock

Lock

<Left side>

<Right side>

Lever

Lever

ACTUATOR OPERATION CHECK

Lever
position

Battery connection Lever

operation

At the
"LOCK"
position

• Connect terminal

No.4 and the
negative battery
terminal.

• Connect terminal

No.6 and the
positive battery
terminal.

The lever
moves from the
"LOCK"
position to the
"UNLOCK"
position.

At the
"UNLOCK"
position

• Connect terminal

No.6 and the
negative battery
terminal.

• Connect terminal

No.4 and the
positive battery
terminal.

The lever
moves from the
"UNLOCK"
position to the
"LOCK"
position.