Mitsubishi Montero (1991+). Manual — part 4
revolutions clockwise. DO NOT rotate counterclockwise. Realign all
timing marks. Tighten belt tensioner bolts to specification. Using
belt tension gauge, measure belt tension halfway between crankshaft
sprocket and camshaft sprocket on side opposite belt tensioner.
7) Belt tension should be 57.3-83.8 lbs. (26-38 kg). To
install remaining components, reverse removal procedure. Install
proper length bolts in timing belt covers. See Fig. 9. Tighten bolts
to specification. See TORQUE SPECIFICATIONS (MONTERO & PICKUP) table.
Fig. 9: Identifying Timing Belt Cover Bolt Lengths (MONTERO & PICKUP)
Courtesy of Mitsubishi Motor Sales of America, Inc.
Fig. 10: Engine Support Bracket Bolt Removal Sequence (3000GT)
Courtesy of Mitsubishi Motor Sales of America, Inc.
NOTE: Apply spray lubricant on reamer bolt during removal as bolt
is sometimes seized in engine support bracket.
Removal (3000GT)
1) Remove lower splash shields. Remove cruise control
actuator (if equipped). Remove all drive belts. Disconnect electrical
connector at power steering pump. Remove A/C tensioner pulley and
mounting bracket.
2) Remove power steering pump with hoses connected, and wire
aside. Support engine. Remove front engine mount through bolt and
front engine mount. Remove timing belt No. 1 upper outer cover and
gaskets. See Fig. 7.
3) Remove engine support bracket bolts in proper sequence.
See Fig. 10. Remove engine support bracket. Remove cover cap and
timing belt No. 2 upper outer cover and gaskets. Using Holder
(MB990767) and Adapter Bolts (MD998719), remove crankshaft pulley.
4) Remove lower outer cover, gaskets and flange. See Fig. 7.
Rotate crankshaft and align all timing marks. See Fig. 8. Loosen belt
tensioner bolt, and rotate belt tensioner counterclockwise to release
belt tension.
5) If reusing timing belt, place arrow on belt to indicate
direction of belt rotation. Remove timing belt and belt tensioner.
6) If camshaft sprocket requires removal, install Holder
(MB990767) with Adapter Bolts (MD998719) on camshaft sprocket. Remove
camshaft sprocket bolt and camshaft sprocket. Remove rear timing belt
cover (if required).
Inspection (3000GT)
Inspect timing belt for wear on edges of drive teeth. Inspect
belt for oil contamination. Replace belt if damaged or contaminated.
Inspect belt tensioner for smooth rotation. Replace if defective.
Installation
1) Install rear timing belt cover. Tighten bolts to
specification. See TORQUE SPECIFICATIONS (3000GT) table at end of
article. Install camshaft sprockets (if removed). Using holder, hold
camshaft and tighten camshaft sprocket bolt to specification.
2) Install belt tensioner and spring. Ensure spring is
secured on pin of water pump and engaged in hole of belt tensioner
with hook of spring pointing from cylinder block.
3) Rotate belt tensioner counterclockwise as much as
possible, and temporarily tighten bolt. Align all timing marks with
No. 1 cylinder at TDC of compression stroke. See Fig. 8.
4) Install timing belt on crankshaft sprocket, rear cylinder
bank camshaft sprocket, water pump pulley, front cylinder bank
camshaft sprocket and timing belt tensioner. Ensure belt is installed
in original direction of rotation and all timing marks are aligned.
Install flange on crankshaft. Loosen belt tensioner bolts slightly,
and allow tensioner to apply belt tension.
5) Using Crankshaft Socket (MD998716), rotate crankshaft 2
revolutions clockwise. DO NOT rotate counterclockwise. Realign all
timing marks. Tighten belt tensioner bolts to specification. See
TORQUE SPECIFICATIONS (3000GT) table. Using belt tension gauge,
measure belt tension halfway between crankshaft sprocket and camshaft
sprocket on side opposite belt tensioner.
6) Belt tension should be 46.3-63.3 lbs. (21-29 kg). To
install remaining components, reverse removal procedure. Install
proper length bolts in timing belt covers and engine support bracket.
See Figs. 9 and 10. Tighten bolts to specification. See TORQUE
SPECIFICATIONS (3000GT) table.
NOTE: Engine support bracket reamer bolt must be tightened slowly
while spraying lubricant on bolt.
Fig. 11: Identifying Timing Belt Cover Bolt Length (SOHC)
Courtesy of Mitsubishi Motor Sales of America, Inc.
Removal (DOHC)
1) Remove lower splash shields. Remove cruise control
actuator (if equipped). Remove all drive belts. Remove alternator.
Remove drive belt tensioner assembly.
2) Using Holder (MB990767) and Adapter Bolts (MD998754),
remove crankshaft pulley. See Fig. 12. Disconnect brake fluid level
sensor. Remove upper timing belt covers. Support engine. Remove front
engine mount through bolt and front engine mount.
NOTE: Apply spray lubricant on reamer bolt during removal as bolt
is sometimes seized in engine support bracket.
Fig. 12: Exploded View of Timing Belt Components (DOHC)
Courtesy of Mitsubishi Motor Sales of America, Inc.
3) Remove drive belt idler pulley. Remove engine support
bracket bolts in proper sequence. See Fig. 10. Remove engine support
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст