Mitsubishi Montero (1991+). Manual — part 1
3.0L V6 - VINS [B,C,S]
1991 Mitsubishi Montero
1991 ENGINES
Mitsubishi 3.0L V6
Montero, Pickup, 3000GT
* PLEASE READ THIS FIRST *
NOTE: For engine repair procedures not covered in this article,
see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article
in the GENERAL INFORMATION section.
ENGINE IDENTIFICATION
Engine may be identified by using Vehicle Identification
Number (VIN) stamped on a metal pad, located near lower left corner of
windshield. The eighth character identifies the engine model.
Engine model number is stamped on front upper edge of
cylinder block (below cylinder head) or on vehicle information plate
on firewall. Engine serial number is stamped near the engine model
number.
ENGINE IDENTIFICATION CODES TABLE
Application Engine Model Engine Code
3.0L V6 SOHC
Montero . . . ... 6G72 . . . . . S
Pickup . . . . 6G72 . . . . . S
3.0L V6 DOHC
3000GT
Non-Turbo . . . 6G72 . . . . . B
Turbo . . . . 6G72 . . . . . C
ADJUSTMENTS
VALVE CLEARANCE ADJUSTMENT
NOTE: Hydraulic lash adjusters are set into rocker arms (SOHC) or
cylinder head (DOHC). No adjustment is required.
REMOVAL & INSTALLATION
NOTE: For reassembly reference, label all electrical connectors,
vacuum hoses and fuel lines before removal. Also place
mating marks on engine hood and other major assemblies
before removal.
FUEL PRESSURE RELEASE
Perform these steps to release fuel system pressure:
* Disconnect fuel pump harness connector at fuel tank.
* Start engine. After it stalls, turn ignition switch to OFF
position.
* Disconnect battery (-) terminal, and reconnect fuel pump
harness connector.
* Wrap shop towels around fuel return and high pressure hoses
to prevent fuel splashing on engine. Disconnect fuel return
hose and high pressure fuel hose to drain any residual fuel.
ENGINE
Removal (Montero & Pickup)
1) Remove hood. Drain cooling system, and remove radiator.
Remove skid plate and splash shields. Release fuel system pressure.
See FUEL PRESSURE RELEASE under REMOVAL & INSTALLATION. Disconnect
negative battery cable.
2) Remove air cleaner ducts. Remove accessory drive belts.
Remove and support A/C compressor and power steering pump. DO NOT
disconnect hoses from compressor or pump. Disconnect oil cooler hoses.
Cover fuel hose using shop towel, and disconnect high pressure fuel
hose and "O" ring. Remove fuel return hose.
3) Label and disconnect all vacuum hoses. Disconnect cooling
system hoses. Label and disconnect all electrical connections from
engine. Remove heat shield from motor mounts. Remove motor mount
bolts. Ensure all hoses and wires are disconnected and set aside.
4) Disconnect exhaust pipe from exhaust manifolds. Remove
starter. Attach engine hoist to engine. Support transmission.
Disconnect engine from transmission. See appropriate article in
CLUTCHES or TRANSMISSION SERVICING. Remove engine.
Installation (Montero & Pickup)
To install, reverse removal procedure. Install new "O" ring
on fuel line. Install new exhaust gaskets and nuts. See TORQUE
SPECIFICATIONS (MONTERO & PICKUP) table at end of article. Adjust
fluid levels.
Removal (3000GT)
1) Release fuel pressure. See FUEL PRESSURE RELEASE under
REMOVAL & INSTALLATION. Remove hood. Remove cruise control vacuum pump
and linkage. On turbo models, remove necessary turbo air intake hoses
and pipes. On all other models, remove air cleaner hoses.
2) On all models, drain cooling system. Drain engine oil and
transaxle oil. Remove heater hoses and radiator hoses. Remove
transaxle assembly. See appropriate article in CLUTCHES or
TRANSMISSION SERVICING.
3) Remove radiator. Label and disconnect all vacuum hoses.
Label and disconnect all electrical connections and harnesses from
engine. Remove accessory drive belts.
4) Remove and support A/C compressor and power steering pump.
DO NOT disconnect hoses from compressor or pump. Cover fuel hose using
shop towel, and disconnect high pressure fuel hose and "O" ring.
Remove fuel return hose.
5) On turbo models, disconnect oil cooler and vacuum hoses.
On all models, remove motor mount bolts and brackets. Ensure all hoses
and wires are disconnected and set aside. Attach engine hoist to
engine. Remove engine.
Installation
To install, reverse removal procedure. Install new "O" ring
on fuel line. Install new exhaust gaskets and nuts. See TORQUE
SPECIFICATIONS (3000GT) table at end of article. Adjust fluid levels.
UPPER INTAKE MANIFOLD
Removal (Montero & Pickup)
1) Remove air intake hose. See Fig. 1. Remove accelerator
cable adjusting bolts. On models equipped with automatic transmission,
remove throttle control cable. On all models, remove accelerator
![](/vehicles/winoney/jueshecothe/henees/que.png)
cable. Label and disconnect all vacuum hoses from throttle body and
upper intake manifold.
2) Disconnect O2 sensor connector. Remove EGR pipe and
gasket. Remove ignition coil. Remove engine oil filler neck bracket.
Remove throttle body, leaving coolant hoses connected. Remove throttle
body gasket. Remove upper intake manifold plenum mounting bolts and
nuts.
3) If necessary, remove EGR valve and pipe. Remove upper
intake manifold plenum brackets. Remove upper intake manifold and
gasket.
Inspection & Installation (Montero & Pickup)
Clean all gasket mating surfaces. Inspect for damage and
cracks on all mounting surfaces. To install, reverse removal procedure
using new gaskets. Tighten bolts and nuts to specification. See TORQUE
SPECIFICATIONS (MONTERO & PICKUP) table at end of article.
Fig. 1: Exploded View of Upper Intake Manifold & Components (DOHC)
Courtesy of Mitsubishi Motor Sales of America, Inc
![](/vehicles/winoney/jueshecothe/henees/yof.png)
Fig. 2: View of Upper Intake Manifold & Components (DOHC Turbo, SOHC)
Courtesy of Mitsubishi Motor Sales of America, Inc
Removal (3000GT)
1) Remove air intake hose. Remove throttle body and gasket
with control cables and coolant and vacuum hoses attached. See Fig. 2.
2) Remove EGR and EGR pipe (if equipped). Disconnect power
brake hose. Label and disconnect vacuum hoses and electrical
connections. Remove upper intake manifold plenum retaining bracket(s),
mounting bolts and nuts. Remove upper intake manifold.
Inspection & Installation (3000 GT)
Clean all gasket mating surfaces. Inspect for damage and
cracks on all mounting surfaces. To install, reverse removal procedure
using new gaskets. Install throttle body gasket with projection on
gasket facing upward beyond throttle body mounting surface. Tighten
bolts and nuts to specification. See TORQUE SPECIFICATIONS (3000GT)
table at end of article.
LOWER INTAKE MANIFOLD
CAUTION: Fuel system is under pressure. Fuel pressure must be
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст