Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 541
DRIVE SHAFT ASSEMBLY
TSB Revision
FRONT AXLE
26-13
CAUTION
•
Do not pull on the driveshaft; doing so will damage the
TJ; be sure to use the pry bar.
•
Do not insert the pry bar so deep as to damage the oil
seal.
•
Do not damage the transaxle oil seal with the spline of
the driveshaft.
2. Insert a pry bar between the transaxle case and the
driveshaft as shown to remove the driveshaft. <2.4L
ENGINE, 3.0L ENGINE-LH>
CAUTION
Do not damage the transaxle oil seal with the spline of the
inner shaft.
3. If the inner shaft and transaxle are tightly joined, tap the
center bearing bracket lightly with a plastic hammer, etc. to
remove the drive shaft and inner shaft from the transaxle.
<3.0L ENGINE-RH>
4. Cover the transaxle case with a shop towel to prevent
foreign material from entering it.
CAUTION
Do not apply the vehicle weight to the wheel bearing while
loosening the driveshaft nut. If, however, the vehicle
weight must be applied to the bearing (in order to move
the vehicle), temporarily secure the wheel bearing by
using special tool MB990998.
AC001157
TRANS-
AXLE
SIDE
AB
PRY BAR
AC001158
AC001159
MB990998
TIGHTEN THE
NUT WITH THE
BOLT SECURED
AB
BOLT
DRIVE SHAFT ASSEMBLY
TSB Revision
FRONT AXLE
26-14
INSTALLATION SERVICE POINTS
>>A<< DRIVESHAFT AND INNER SHAFT/DRIVESHAFT
INSTALLATION
CAUTION
•
Do not damage the transaxle oil seal with the spline of
the shaft.
•
Do not damage the ABS rotor attached to the BJ outer
race <Vehicles with ABS>.
>>B<< DRIVESHAFT NUT INSTALLATION
1. Face the flat side of a washer to a driveshaft nut to install.
CAUTION
Do not apply pressure to wheel bearing by the vehicle
weight to avoid possible damage when driveshaft nut is
loosened.
2. Use special tool MB990767 to fix the hub and tighten the
driveshaft nut.
3. If the position of the cotter pin holes does not match, tighten
the nut up to 255 N
⋅
m (188 ft-lb) maximum.
4. Install the cotter pin in the first matching holes and bend it
securely.
AC001151
WASHER
MB990767
226 ± 29 N·m
167 ± 21 ft-lb
AB
DRIVE SHAFT ASSEMBLY
TSB Revision
FRONT AXLE
26-15
INSPECTION
M1261003600084
•
Check the driveshaft boot for damage or deterioration.
•
Check the ball joints for excessive play or poor operating
condition.
•
Check the spline part for wear or damage.
DRIVE SHAFT ASSEMBLY
TSB Revision
FRONT AXLE
26-16
DISASSEMBLY AND ASSEMBLY
M1261003700081
CAUTION
Never disassemble the BJ assembly except when replacing the BJ boot.
AC001160
<3.0L ENGINE-RH>
3
7
7
6
N
13
4
5
N
N
10
11
12
N
9
N
8
N
13
4
14
N
15
16
N
1
2
N
18
N
19
17
10
12
11
9
13
BRACKET ASSEMBLY
REPAIR KIT
10
11
9
13
BEARING DUST SEAL
REPAIR KIT
13
14
16
1
2
TJ BOOT REPAIR KIT
13 14 1
2
18
21
20
22
BJ BOOT REPAIR KIT
13
4
14
15 16
1
2
TJ REPAIR KIT
AB
<2.4L ENGINE, 3.0L ENGINE-LH>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст