Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 618
WINDOW GLASS
TSB Revision
BODY
42-19
>>D<< ROOF DRIP MOLDING INSTALLATION
Install the clip to the roof drip molding before installing the
molding to the vehicle body.
QUARTER WINDOW GLASS
REMOVAL AND INSTALLATION
M1422002500065
Pre-removal and Post-installation Operation
•
Quarter Trim Upper Removal and Installation (Refer to
GROUP 52A
.)
AC000458
1
2
A
A
B
B
C
C
SECTION A – A
mm (in)
20 (0.8)
15
(0.6)
35 (1.4)
PRIMER
SECTION C – C
SECTION B – B
15 (0.6)
15 (0.6)
PRIMER
15 (0.6)
15 (0.6)
PRIMER
ADHESIVE: 3M™ AAD PART NO.8609 SUPER FAST URETHANE AND 3M™ AAD PART NO.8608 SUPER FAST
URETHANE PRIMER OR EQUIVALENT
AB
3
WINDOW GLASS
TSB Revision
BODY
42-20
REMOVAL SERVICE POINT
<<A>> QUARTER WINDOW GLASS REMOVAL
1. Apply cloth tape to protect quarter window glass.
CAUTION
Putting glass adhesive knife too deeply into windshield
adhesive may damage quarter window glass.
2. Use glass adhesive knife to cut away adhesive.
Keep glass adhesive knife at right angles with body flange
(from inside the vehicle), and put the blade at body flange.
Then cut away adhesive along the body flange.
NOTE: If glass adhesive knife does not reach the body
flange, refer to WINDSHIELD
.
3. Make mating marks on the quarter window glass and body.
4. Use special tool MB990480 to remove the quarter window
glass.
REMOVAL STEPS
<<A>> >>A<<
1. QUARTER WINDOW GLASS AS-
SEMBLY
2. PACKING
3 . CLIP
REMOVAL STEPS (Continued)
AC002057AB
CLOTH TAPE
AC002060
AC002061
GLASS ADHESIVE
KNIFE
AB
AC002058
MB990480
AB
WINDOW GLASS
TSB Revision
BODY
42-21
CAUTION
•
Be careful not to remove more adhesive than is
necessary.
•
Be careful also not to damage the paintwork on the
body surface with the knife. If the paintwork is
damaged, repair the damaged area with repair paint or
anti-rust agent.
5. Use a knife to cut away the remaining adhesive so that the
thickness is within 2 mm (0.08 inch) around the entire
circumference of the body flange.
6. Finish the flange surfaces so that they are smooth.
CAUTION
Allow the cleaned area to dry for at least three minutes. Do
not touch any surface that has been cleaned.
7. When reusing the quarter window glass, remove the
adhesive still adhering to the quarter window glass, and
clean with 3M
AAD Part number 8906 or equivalent.
8. Clean the body side in the same way.
INSTALLATION SERVICE POINT
>>A<< QUARTER WINDOW GLASS INSTALLATION
1. Carry out the following procedure to re-install quarter
window glass.
CAUTION
Do not forget packing.
(1) Fit clips into body.
(2) Cut away clip fitting convex on quarter window glass.
NOTE: Convex gets broken when quarter window glass
is removed.
2. Remove the quarter window glass using the same
procedure as for the windshield remove. (Refer to
.)
ACX00476 AB
AC002172AB
CUT OFF THESE PARTS
WINDOW GLASS
TSB Revision
BODY
42-22
LIFT GATE WINDOW GLASS
REMOVAL AND INSTALLATION
M1422003700040
Pre-removal and Post-installation Operation
•
Liftgate Trim Removal and Installation (Refer to
•
Rear Wiper Arm, Wiper Motor and Washer Nozzle
Removal and Installation (Refer to GROUP 51
AC000459AB
A
A
B
B
6
9
SECTION A – A
6
9
6
SECTION
B – B
ADHESIVE TAPE: DOUBLE-SIDED TAPE [6 mm (0.2 in) WIDE AND 0.125 mm (0.0049) THICK] AND 3M™ AAD
PART NO.8608 SUPER FAST URETHANE PRIMER OR EQUIVALENT
C
C
D
D
E
E
6
SECTION C – C
SECTION D – D
SECTION E – E
9
6
7
9
6
9
8 ± 1 (0.3 ± 0.04)
43 (1.7) 20 (0.8)
15 (0.6)
PRIMER
mm (in)
8 ± 0.5
(0.3 ± 0.02)
20 (0.8)
8 (0.3)
15 (0.6)
PRIMER
25 (1.0)
4.5 ± 1.5
(0.2 ± 0.1)
15
(0.6)
21
(0.8)
15.5
(0.6)
PRIMER
ADHESIVE: 3M™ AAD PART NO. 8609 SUPER FAST URETHANE AND 3M™ AAD PART NO.8608 SUPER FAST
URETHANE PRIMER OR EQUIVALENT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст