Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 685
![](/vehicles/winoney/isene/butrele/padouevesp.png)
SRS CONTROL UNIT (SRS-ECU)
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-67
REMOVAL AND INSTALLATION
REMOVAL SERVICE POINT
<<A>> NEGATIVE (-) BATTERY CABLE DISCONNECTION
DANGER
Wait at least 60 seconds after disconnecting the
battery cable before doing any further work. (Refer to
.)
WARNING
Battery posts, terminals and related accessories
contain lead and lead compounds. WASH HANDS
AFTER HANDLING.
Disconnect the negative battery cable from the battery and
tape the terminal to prevent accidental connection and
deployment.
Pre-removal Operation
•
Turn the ignition switch to "LOCK" (OFF) position.
•
Floor Console Removal (Refer to GROUP 52A, Floor
Console
Post-installation Operation
•
Floor Console Installation (Refer to GROUP 52A, Floor
Console
.)
AC003160AB
1
2
3
4.9 ± 1.0 N·m
44 ± 8 in-lb
4.9 ± 1.0 N·m
44 ± 8 in-lb
REMOVAL STEPS
<<A>>
1.
NEGATIVE (-) BATTERY CABLE
CONNECTION
2.
BRACKET MOUNTING BOLT
(GROUNDING BOLT)
3.
SRS-ECU
INSTALLATION STEPS
>>A<<
3.
SRS-ECU
>>B<<
2.
BRACKET MOUNTING BOLT
(GROUNDING BOLT)
1.
NEGATIVE (-) BATTERY CABLE
CONNECTION
>>C<<
•
POST-INSTALLATION
INSPECTION
ACX00583
INSULATING TAPE
BATTERY
BATTERY CABLE (–)
AC
![](/vehicles/winoney/isene/butrele/xyansimotuty.png)
SRS CONTROL UNIT (SRS-ECU)
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-68
INSTALLATION SERVICE POINTS
>>A<< SRS-ECU INSTALLATION
WARNING
The SRS may not activate if the SRS-ECU is not
installed properly, which could result in serious injury
or death to the vehicle's driver or front passenger.
>>B<< BRACKET MOUNTING BOLT (GROUNDING BOLT)
INSTALLATION
Check the head mark "E" on the bolt and attach the grounding
bolt.
>>C<< POST-INSTALLATION INSPECTION
1. Reconnect the negative (-) battery cable.
2. Turn the ignition switch to "ON" position.
3. Does the "SRS" warning light illuminate for approximately 7
seconds, and then remain off for at least 5 seconds after
turning "OFF."
4. If yes, the SRS system is functioning properly. If no, refer to
.
INSPECTION
M1524002200067
WARNING
If a dent, crack, deformation or rust is discovered,
replace the SRS-ECU with a new one.
•
Check the SRS-ECU and brackets for dents, cracks or
deformation.
•
Check the SRS-ECU connector for damage, and the
terminals for deformation.
NOTE: Refer to
for inspection of SRS-ECU for other
than physical damage.
ACX00599AB
EARTH BOLT HEAD MARK
AC000346AB
SRS WARNING LIGHT
![](/vehicles/winoney/isene/butrele/iss.png)
AIR BAG MODULE(S) AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-69
A IR B A G M O D U LE(S) A N D C LO C K SPR IN G
AIR BAG MODULE(S) AND CLOCK SPRING REMOVAL AND INSTALLATION
M1524002400072
WARNING
•
Never attempt to disassemble or repair the air bag modules or clock spring. If faulty,
replace it.
•
Do not drop the air bag modules or clock spring or allow contact with water, grease or oil.
Replace it if a dent, crack, deformation or rust is detected.
•
The air bag modules should be stored on a flat surface is facing upward. Do not place
anything on top of it.
•
Do not expose the air bag modules to temperatures over 93
°
C (200
°
F).
•
After deployment of an air bag, replace the clock spring with a new one.
•
Wear gloves and safety glasses when handling air bags that have already deployed.
•
An undeployed air bag module should only be disposed of in accordance with the
procedures. (Refer to
<Side air bag module>
For removal and installation of the front seatback assembly with side air bag module, refer to GROUP 52A,
Front Seat
REMOVAL AND INSTALLATION
<Air bag module (driver's side), clock spring>
AC002990AB
1
2
3
4
5
41 ± 8 N·m
31 ± 5 ft-lb
9.0 ± 2.0 N·m
78 ± 17 ft-lb
N
AIR BAG MODULE REMOVAL
STEPS
<<A>>
1. NEGATIVE (-) BATTERY CABLE
CONNECTION
<<B>>
2. AIR BAG MODULE (DRIVER'S SIDE)
CLOCK SPRING REMOVAL STEPS
<<A>>
1. NEGATIVE (-) BATTERY CABLE
CONNECTION
<<B>>
2. AIR BAG MODULE (DRIVER'S SIDE)
<<C>>
3. STEERING WHEEL
![](/vehicles/winoney/isene/butrele/uthe.png)
AIR BAG MODULE(S) AND CLOCK SPRING
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-70
Required Special Tools:
•
MB990502: Scan Tool (MUT-II)
•
MB990803: Steering Wheel Puller
•
MB991613: SRS Check Harness
(front passenger's side)>
4. COLUMN COVER LOWER
<<D>>
5. CLOCK SPRING
AIR BAG MODULE INSTALLATION
STEPS
>>A<<
•
PRE-INSTALLATION INSPECTION
>>D<<
2. AIR BAG MODULE (DRIVER'S SIDE)
1. NEGATIVE (-) BATTERY CABLE
CONNECTION
>>E<<
•
POST-INSTALLATION INSPECTION
CLOCK SPRING INSTALLATION
STEPS
>>A<<
•
PRE-INSTALLATION INSPECTION
>>B<<
5. CLOCK SPRING
4. COLUMN COVER LOWER
CLOCK SPRING REMOVAL STEPS
>>C<<
3. STEERING WHEEL
>>D<<
2. AIR BAG MODULE (DRIVER'S SIDE)
1. NEGATIVE (-) BATTERY CABLE
CONNECTION
>>E<<
•
POST-INSTALLATION INSPECTION
CLOCK SPRING INSTALLATION
STEPS (Continued)
AC000698AB
4
3
2
1
AIR BAG MODULE REMOVAL
STEPS
<<A>>
1. NEGATIVE (-) BATTERY CABLE
CONNECTION
2. GLOVE BOX OUTER
3. GLOVE BOX INNER
<<E>>
4. AIR BAG MODULE (FRONT
PASSENGER'S SIDE)
AIR BAG MODULE INSTALLATION
STEPS
>>A<<
•
PRE-INSTALLATION INSPECTION
4. AIR BAG MODULE (FRONT
PASSENGER'S SIDE)
3. GLOVE BOX INNER
2. GLOVE BOX OUTER
1. NEGATIVE (-) BATTERY CABLE
CONNECTION
>>E<<
•
POST-INSTALLATION INSPECTION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст