Acura RL (1996-2004 year). Manual — part 577
4-way power adjustable (with seat heater):
for the seat wire harness installation.
HEADREST
BACK COVER
HOOKS
SEAT-BACK
HOOK
POWER SEAT
SWITCH
POWER SEAT
HARNESS
Installation is the reverse of the removal procedure.
CLIP
To seat cushion
cover.
NOTE:
Make sure the bushing and pivot washer are installed properly.
To prevent wrinkles when installing the seat-back cover, make sure the material is stretched evenly over the pad.
Grease the sliding portion.
SEAT-BACK
HEATER
CONNECTOR
SEAT CUSHION
CLIPS
PIVOT NUT
8 x 1.25 mm
22 N-m (2.2 kgf-m,
16 Ibf-ft)
SEAT HEATER
CONNECTOR
PIVOT
WASHER
SIDE AIRBAG
CONNECTOR
('99 - 01 models)
OPDS UNIT
CONNECTOR
('99 - 01 models)
BUSHING
CLIP
To seat cushion
cover.
10 x 1.25 mm
47 N-m (4.8 kgf-m,
35 Ibf-ft)
RECLINE
COVER
KNOBS
CAP
RECLINE
ADJUSTER
COVER
10 x 1.25 mm
47 N-m (4.8 kgf-m,
35 Ibf-ft)
CENTER
COVER
Disassembly
Main Menu
Table of Contents
Front Seat
SEAT-BACK
4. For the driver's seat, remove the lumbar support
knob.
CLIP
5. Loosen the seat-back cover by releasing all the
hooks.
'96 - 98 models
SEAT-BACK
COVER
HOOK
HOOK
HOOKS
'99 - 01 models
CAUTION: Do not touch the Occupant Position
Detection System (OPDS) sensor in the cushion.
Keep the sensor free from oils. Oils can corrode the
sensor, causing its faulty.
SEAT-BACK
COVER
HOOKS
HOOK
HOOK
HOOK
HOOK
HOOK
LUMBAR
SUPPORT
KNOB
HEADREST
GUIDES
Seat Cover Replacement
SRS components are located in this area. Review the
SRS component locations, precautions, and procedures
in the Restraints (
) before performing repairs
or service.
CAUTION: Put on gloves to protect your hands.
NOTE:
Seats with airbags are marked "SIDE AIRBAG" on the
seat-back. Because the component parts (seat-back
cover, cushion, etc.) of seats with and without
airbags are different, make sure you install only the
correct replacement parts.
Do not repair torn or frayed seat-back covers. If nec-
essary, replace the seat-back cover.
Take care not to tear the seams or damage the seat
covers.
Seat-back cover removal:
1. Slide the front seat forward, and fold the seat-back
forward.
2. Remove the back cover (see pages
).
3. Remove the headrest and headrest guides.
KNOB
HEADREST
GUIDE
Main Menu
Table of Contents
Pull back the edge of the seat-back cover all the way
around, release the clips, and remove the seat-back
cover.
'96 - 98 models
SEAT-BACK
COVER
CLIP
'99 - 01 models
CLIP
SEAT-BACK
COVER
7. Installation is the reverse of the removal procedure.
NOTE:
To prevent wrinkles when installing a seat-back
cover, make sure the material is stretched evenly
over the pad before securing the hooks and clips.
Replace the released clips with new ones.
Use only original Acura replacement seat-back
covers ('99 - 01 models).
Main Menu
Table of Contents
Front Seat
Seat Cover Replacement (cont'd)
Seat cushion cover removal:
1. Remove the seat cushion (see pages
).
2. Remove the clips and hooks from under the seat
cushion, then remove the seat cushion cover with
the pad from the seat cushion frame.
HOOKS
HOOKS
HOOKS
PAD
CLIPS
SEAT CUSHION
FRAME
3. Pull back the edge of the seat cushion cover all the
way around, release the clips, and remove the seat
cushion cover.
CLIP
SEAT CUSHION
COVER
4. Installation is the reverse of the removal procedure.
NOTE:
To prevent wrinkles when installing a seat cush-
ion cover, make sure the material is stretched
evenly over the pad before securing the clips and
hooks.
Replace the released clips with new ones.
SEAT
COVER
UPHOLSTERY RING PLIERS
(Commercially available)
NEW CLIP
PAD
WIRE (Pad side)
WIRE
(Cover side)
Main Menu
Table of Contents
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст