Defender (1999-2002). Manual — part 136
![](/vehicles/onond/ycatth/que/selarore.png)
86
ELECTRICAL
16
REPAIR
LAMP ASSEMBLY - CENTRE HIGH MOUNTED
STOP LIGHT (CHMSL) - FROM 02MY
Service repair no - 86.41.32
Remove
1. Open rear door.
2. Remove 2 screws and cover from CHMSL.
3. Remove insulated cover from Lucar connector,
release catch’s and disconnect Lucar’s taking
care not to damage screen element.
4. Remove nuts securing lamp to rear screen,
withdraw lamp assembly, collect seals and
washers.
5. Remove rubber backing pad, taking care not to
damage screen obscuration band.
Refit
6. Clean obscuration band and fit new backing pad.
7. Fit lamp assembly, seals and washers. Fit nuts
and tighten to 3 Nm (2.2 lbf.ft) .
8. Insulate Lucar connector.
9. Connect Lucars to heated rear screen.
10. Fit cover to CHMSL and secure with screws.
FLASHER UNIT - HAZARD WARNING - FROM
02MY
Service repair no - 86.55.12
Service repair no - 86.55.15
NOTE: This procedure also covers
removal of the Heated Front Screen Timer
Relay, 86.55.15.
Remove
1. Disconnect battery negative lead. See this
Section.
2. Remove 4 screws securing instrument pack and
release pack from fascia.
3. Disconnect 2 multiplugs from warning lamp
panel.
4. Disconnect instrument pack multiplug from main
harness.
5. Remove instrument pack.
![](/vehicles/onond/ycatth/que/velo.png)
ELECTRICAL
17
REPAIR
6. Identify and remove relay.
NOTE: Flasher unit shown.
Refit
7. Fit relay.
8. Position instrument pack and connect multiplugs.
9. Fit instrument pack to fascia and secure with
screws.
10. Connect battery negative lead. See this
Section.
RELAY - HEATED FRONT SCREEN - FROM 02MY
Service repair no - 86.55.18
Remove
1. Remove front seat cushion.
2. Release clip and remove compartment cover.
3. Locate and release relay from bracket.
4. Remove relay.
Refit
5. Fit relay.
6. Fit relay to mounting bracket.
7. Fit and secure cover.
8. Fit seat cushion.
![](/vehicles/onond/ycatth/que/arsh.png)
86
ELECTRICAL
18
REPAIR
RELAY - REAR FOG GUARD - FROM 02MY
Service repair no - 86.55.53
Remove
1. Disconnect battery negative lead. See this
Section.
2. Remove 4 screws securing instrument pack and
release pack from fascia.
3. Disconnect 2 multiplugs from warning lamp
panel.
4. Disconnect instrument pack multiplug from main
harness.
5. Remove instrument pack.
6. Remove screw securing relay bracket,
disconnect multiplug and remove relay.
Refit
7. Fit relay, connect multiplug and secure relay with
screw.
8. Position instrument pack and connect multiplugs.
9. Fit instrument pack to fascia and secure with
screws.
10. Connect battery negative lead. See this
Section.
![](/vehicles/onond/ycatth/que/ftathoh.png)
ELECTRICAL
19
REPAIR
RELAY - STARTER - FROM 02MY
Service repair no - 86.60.10
Remove
1. Remove 2 screws securing fuse cover and
remove cover.
2. Identify and remove relay.
Refit
3. Fit relay.
4. Fit fuse cover and secure with screws.
SWITCH - HEADLAMP LEVELLING - FROM 02MY
Service repair no - 86.65.16
Remove
1. Disconnect battery negative lead. See this
Section.
2. Remove fascia console. See CHASSIS AND
BODY, Repair.
3. Remove operating knob from light switch.
4. Remove nut securing light switch and remove
switch from console.
Refit
5. Fit light switch and secure with nut.
6. Fit operating knob to switch.
7. Fit fascia console. See CHASSIS AND BODY,
Repair.
8. Connect battery negative lead. See this
Section.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст