Defender 300Tdi (1996+). Manual — part 84
76
CHASSIS AND BODY
20
REPAIR
REAR SEAT BELTS - 90/110 STATION WAGON,
INWARD FACING SEATS
Service repair no - 76.73.18
Remove
1. Release belt straps from buckles.
2. Release stowage straps and lower both seat
cushions.
3. Unscrew bolt securing lap strap to body
mounting.
4. Remove lap strap, wavy washer, spacer and
plain washer.
5. Repeat operation for buckle strap.
Refit
6. Secure lap strap and buckle straps to body.
Tighten bolts to
32 Nm (24 lbf/ft).
7. If required, secure seat cushions and belts in
stowed position.
REAR SEAT BELTS - 110
Service repair no - 76.73.18
Remove
1. Remove rear inward facing seats
See Rear
seat squab - 90 or See Rear bench seat .
2. Remove side trim panel
See Side trim panel .
3. Remove bolt securing seat belt inertia reel to ’C’
post.
4. Remove seat belt assembly.
5. Pull seat belt straps between seat cushion and
squab into rear of vehicle.
6. Remove finisher cap and bolt securing seat belt
anchorage to floor.
7. Remove seat belt assembly.
CHASSIS AND BODY
21
REPAIR
Refit
8. Secure seat belt straps to floor mounting.
Tighten bolt to
32 Nm (24 lbf/ft) and fit finisher
cap.
9. Feed belt straps between seat cushion and
squab.
10. Fit inertia reel to ’C’ post. Tighten bolt to
32 Nm
(24 lbf/ft).
11. Fit side trim panel
See Side trim panel .
12. Fit rear inward facing seats
See Rear seat
squab - 90 or See Rear bench seat .
SIDE TRIM PANEL - 90 STATION WAGON
Service repair no - 76.13.70
Remove
1. Remove rear seat squabs
See Rear seat
squab .
2. Remove rear end trim panel
See Rear end
trim panel .
3. Prise cap from front seat belt upper guide
retaining bolt.
4. Unscrew retaining bolt and remove seat belt
from ’B’ post.
5. Carefully prise trim stud from ’B’ post.
6. Remove 4 bolts securing side trim panel to body
side.
7. Release top edge of side trim panel by striking
upwards with the hand to disengage 3 spring
clips.
8. Lift trim panel from window surround and remove
from vehicle.
76
CHASSIS AND BODY
22
REPAIR
Refit
9. Fit new spring clips to the 3 brackets on top
edge of side trim panel.
10. Align trim panel, ensuring it is correctly
positioned around side window.
11. Locate trim panel spring clips on inner cant rail
and press firmly down to secure top edge of trim
panel.
12. Align bosses of trim panel with body side fixing
holes and secure with 4 bolts and washers. Do
not fully tighten at this stage.
13. Fit trim stud to secure bottom edge of trim panel
to ’B’ post.
14. Secure seat belt guide to ’B’ post, tighten bolt to
32 Nm (24 lbf/ft) and fit cap.
15. Fit rear end trim panel
See Rear end trim
panel .
16. Fit rear seat squab
See Rear seat squab .
SIDE TRIM PANEL - 110 STATION WAGON
Service repair no - 76.13.70
Remove
1. Remove rear inward facing seats
See Rear
seat squab - 90 , or See Rear bench seat .
2. Remove rear end trim panel
See Rear end
trim panel .
3. Prise finisher cap from rear seat belt upper guide
bracket retaining bolt.
4. Unscrew bolt and remove guide bracket from ’C’
post.
5. Remove bolt securing seat belt to wheel arch
mounting.
6. Prise trim panel cap fastener from ’C’ post.
7. Remove seat belt aperture finisher from side trim
panel.
8. Remove screw and release seat belt clip from ’C’
post.
CHASSIS AND BODY
23
REPAIR
9. Remove fixings securing bottom edge of trim
panel to body side.
10. Release top edge of trim panel by striking
upwards with the hand to disengage 3 spring
clips.
11. Lift trim panel from window surround and feed
seat belt through panel aperture.
12. Remove trim panel from vehicle.
Refit
13. Fit new spring clips to the 3 brackets on top
edge of side trim panel.
14. Feed seat belt through aperture in trim panel and
fit finisher.
15. Align trim panel, ensuring it is correctly
positioned around side window.
16. Locate trim panel spring clips on inner cant rail
and press firmly down to secure top edge of trim
panel.
17. Align bosses of trim panel with body side fixing
holes and secure with bolts or screws. If
individual type seats are fitted do not fully tighten
fixings at this stage.
18. Fit seat belt clip to ’C’ post.
19. Fit trim panel cap fastener to ’C’ post.
20. Fit seat belt to wheel arch. Tighten bolt to
32 Nm
(24 lbf/ft).
21. Fit seat belt guide bracket to ’C’ post. Tighten
bolt to
32 Nm (24 lbf/ft) and fit finisher cap.
22. Fit rear end trim panel
See Rear end trim
panel .
23. Fit inward facing seats
See Rear seat squab ,
or
See Rear bench seat .
REAR END TRIM PANEL - 90/110 STATION
WAGON
Service repair no - 76.13.71
Remove
1. Pull edge of rear end trim panel firmly to release
2 spring retaining clips from vertical rail at door
aperture.
2. Remove rear end trim panel.
Refit
3. Fit new spring clips to the 2 brackets on side of
trim panel.
4. Position outboard edge of trim panel in corner to
abut side trim panel and locate spring clips on
vertical rail.
5. Press edge of trim panel firmly to secure in
position.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст