Discovery 2. Manual — part 248
![](/vehicles/onond/myas/hellowhomsel/ouglli.png)
SEATS
REPAIRS 76-5-23
Bladder - lumbar support
$% 78.60.01
Remove
1. Remove squab cover.
SEATS, REPAIRS, Cover - squab -
2. Disconnect lumbar support pump multiplug.
3. Release lumbar support pump from bladder
retainers.
4. Release bladder from 8 retainers and remove
bladder and lumbar support pump.
5. Collect bladder retainers.
Refit
1. Position bladder retainers to seat frame.
2. Position bladder and secure to bladder
retainers
3. Position pump in bladder retainers and
connect multiplug.
4. Fit squab cover.
SEATS, REPAIRS, Cover - squab -
Motor - fore and aft - front seat
$% 78.70 25
Remove
1. Remove front seat.
2. Disconnect multiplug from fore and aft motor.
3. Remove Allen screw securing RH screw
thread to seat frame.
4. Remove 2 retainers from RH fore and aft
gearbox roll pin. Remove roll pin.
5. Remove spacers.
6. Position RH screw thread retainer clear of seat
frame and remove fore and aft motor.
Refit
1. Clean gearbox and motor drive tube.
2. Position motor drive tube to LH gearbox and
align fore and aft motor to seat frame.
3. Fit new gearbox spacers, roll pin and retainers.
4. Align RH screw thread retainer to seat frame
and secure with Allen screw.
Ensure retainer is correctly aligned or
damage may occur when seat motor is
operated.
5. Connect fore and aft motor multiplug.
6. Fit front seat.
![](/vehicles/onond/myas/hellowhomsel/eranas.png)
SEATS
76-5-24 REPAIRS
Motor - rise and fall - front seat
$% 78.70.27
Remove
1. Remove front seat.
2. Disconnect multiplug from rise and fall motor.
3. Remove retainers from roll pins.
4. Using a suitable drift remove roll pins securing
rise and fall motor and operating lever to seat
frame.
5. Remove rise and fall motor.
Refit
1. Position and align rise and fall motor to seat
frame.
2. Fit new roll pins to secure rise and fall motor
and operating lever.
3. Fit new retainers to roll pins.
4. Connect multiplug to rise and fall motor.
5. Fit front seat.
Motor - tilt - front seat
$% 78.70.29
Remove
1. Remove front seat.
2. Disconnect multiplug from tilt motor.
3. Remove 2 retainers and 'C' clip from roll pins
securing tilt motor.
4. Using a suitable drift remove roll pins securing
tilt motor and operating lever to seat frame.
5. Remove tilt motor.
Refit
1. Position and align tilt motor to seat frame.
2. Fit new roll pins to secure motor and operating
arm.
3. Fit new retainers and 'C' clip to roll pins.
4. Connect multiplug to tilt motor.
5. Fit front seat.
![](/vehicles/onond/myas/hellowhomsel/owo.png)
SEATS
REPAIRS 76-5-25
Motor - recline
$% 78.70.34
Remove
1. Remove squab cover.
SEATS, REPAIRS, Cover - squab -
2. Disconnect recline motor multiplug.
3. Remove 2 bolts securing recline motor and
remove motor.
Refit
1. Position recline motor and ensure gear and
gear spigot are engaged.
2. Fit and tighten bolts securing recline motor to
frame.
3. Connect recline motor multiplug.
4. Fit squab cover.
SEATS, REPAIRS, Cover - squab -
Switch - electric seats
$% 78.70.88
Remove
1. Release switch from centre console.
2. Pull the connector retaining bar outwards to the
limit of its travel and carefully disconnect the
connector from the switch.
Refit
1. Connect multiplug to rear of switch and slide
the retaining bar fully home.
2. Fit switch to centre console.
![](/vehicles/onond/myas/hellowhomsel/derzaweve.png)
SEATS
76-5-26 REPAIRS
Cable - rear squab latch
$% 78.80.04
Remove
1. Remove rear seat squab latch mechanism.
SEATS, REPAIRS, Latch - rear seat.
2. Remove rear seat squab release cable.
Refit
1. Position seat release cable.
2. Fit latch assembly.
Latch - rear seat
$% 78.80.12
Remove
1. Remove 3 screws securing seat end cover and
remove from seat assembly.
2. Carefully release 11 clips securing seat
assembly backboard.
3. Remove seat assembly backboard.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст