Nissan March K13. Manual — part 100
HOOD
DLK-111
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOVAL AND INSTALLATION
HOOD
Exploded View
INFOID:0000000005948964
HOOD ASSEMBLY
HOOD ASSEMBLY : Removal and Installation
INFOID:0000000005948965
CAUTION:
• Operate with two workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
REMOVAL
1.
Support hood assembly with the proper material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported by the proper material when removing hood
assembly.
2.
Remove hood hinge mounting nuts on the hood to remove the hood assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check hood hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, apply touch-up paint (the body color) onto the heads of hood hinge mounting bolts
and nuts.
1.
Hood assembly
2.
Hood bumper rubber
3.
Hood hinge (LH)
4.
Grommet
5.
Hood hinge (RH)
6.
Hood support rod
7.
Clamp
Refer to
JMKIA5289ZZ
DLK-112
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
• After installing, perform hood fitting adjustment. Refer to
DLK-112, "HOOD ASSEMBLY : Adjust-
HOOD ASSEMBLY : Adjustment
INFOID:0000000005948966
Check the clearance and the surface height between hood and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1.
Hood assembly
2.
Hood bumper rubber
3.
Hood hinge
4.
Hood lock assembly
5.
Front bumper fascia
6.
Front combination lamp
7.
Front fender
Refer to
for symbols in the figure.
Portion
Standard
Difference
(RH/LH,
MAX)
Hood – Front
bumper fascia
A – A
D
Clearance
2.4 – 6.4 (0.094 – 0.252)
—
E Surface height (-2.5) – (+1.5) [(-0.098) – (+0.059)]
—
Hood – Front combi-
nation lamp
B – B
F
Clearance
1.9 – 6.1 (0.075 – 0.240)
< 2.0 (0.079)
G Surface height (-2.6) – (+2.6) [(-0.102) – (+0.102)]
< 2.0 (0.079)
JMKIA5290GB
HOOD
DLK-113
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Remove hood lock and adjust the surface height of hood, front bumper fascia, front combination lamp and
front fender according to the fitting standard dimension, by rotating hood bumper rubber.
2.
Loosen hood hinge mounting nuts on the hood.
3.
Adjust the clearance of hood, front bumper fascia, front combination lamp and front fender according to
the fitting standard dimension, for the hood.
4.
Temporarily tighten hood lock.
5.
Check that hood lock secondary latch is securely engaged with striker by dropping hood from approxi-
mately 200 mm (7.874 in) height or by pressing lightly on the hood.
CAUTION:
Never drop hood from a height of 300 mm (11.811 in) or more
6.
Install as static closing face of hood is 94– 490 N (9.6 – 50.0 kg, 21.1 – 110 lb).
7.
After adjustment tighten lock bolts to the specified torque.
CAUTION:
• Check hood hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, apply touch-up paint (the body color) onto the heads of hood hinge mounting bolts
and nuts.
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000005948968
REMOVAL
1.
Remove hood assembly. Refer to
DLK-111, "HOOD ASSEMBLY : Removal and Installation"
.
2.
Remove front fender. Refer to
DLK-116, "Removal and Installation"
.
3.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check hood hinge rotating part for poor lubrication. If necessary, apply grease.
• After installation, apply touch-up paint (the body color) onto the head of the hinge mounting bolts
and nuts.
• After installation, perform hood fitting adjustment. Refer to
DLK-112, "HOOD ASSEMBLY : Adjust-
HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000005948970
REMOVAL
1.
Support hood assembly with a suitable material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported by the proper material when removing hood
assembly.
2.
Pull hood support rod from grommet and remove.
INSTALLATION
Install in the reverse order of removal.
Hood – Front fender
C – C
H
Clearance
2.5 – 4.5 (0.098 – 0.177)
< 1.0 (0.039)
I
Surface height
(-1.5) – (+0.5) [(0.059) – (+0.020)]
< 1.5 (0.059)
Portion
Standard
Difference
(RH/LH,
MAX)
DLK-114
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000005948971
Removal and Installation
INFOID:0000000005948972
RADIATOR CORE SUPPORT UPPER
Removal
1.
Remove washer tank inlet. Rwfer to
WW-47, "Removal and Installation"
2.
Remove ground harness (1) mounting bolt (A).
3.
Disconnect horn connector.
4.
Remove horn mounting nut, and remove horn.
5.
Remove hood lock and hood lock cable fixing clip. Refer to
DLK-131, "Removal and Installation"
.
1.
Radiator core support upper
2.
Condenser side seal
3.
Radiator side seal (RH)
4.
Radiator upper seal
5.
Radiator side seal (LH)
6.
Radiator core support lower
JMKIA5291ZZ
JMKIA5293ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст