Nissan Qashqai (2007-2010). Manual — part 712
BRC-46
< COMPONENT DIAGNOSIS >
[ABS]
BRAKE FLUID LEVEL SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace malfunctioning components.
Component Inspection
INFOID:0000000000925046
1.
CHECK BRAKE FLUID LEVEL SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect brake fluid level switch connector.
3.
Check continuity between brake fluid level switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace reservoir tank.
Combination meter
—
Continuity
Connector
Terminal
M34
27
Ground
Not existed
Brake fluid level switch
—
Continuity
Connector
Terminal
E37
2
Ground
Existed
Brake fluid level switch
Condition
Continuity
Connector
Terminal
E37
1 – 2
When brake fluid is full in the reservoir tank.
Not existed
When brake fluid is empty in the reservoir tank.
Existed
PARKING BRAKE SWITCH
BRC-47
< COMPONENT DIAGNOSIS >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
PARKING BRAKE SWITCH
Description
INFOID:0000000000925052
The parking brake switch converts the status of the parking brake pedal to an electric signal and transmits it to
the ABS actuator and electric unit (control unit).
Diagnosis Procedure
INFOID:0000000001125317
1.
CHECK COMBINATION METER INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between combination meter harness connector terminal 26 and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and parking brake switch connector.
3.
Check continuity between combination meter harness connector terminal 26 and parking brake switch
harness connector terminal 1.
4.
Check continuity between combination meter harness connector terminal 26 and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Component Function Check
INFOID:0000000000925053
1.
CHECK PARKING BRAKE SWITCH OPERATION
Operate the parking brake pedal. Then check that the brake warning lamp in the combination meter turns on/
off correctly.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to diagnosis procedure. Refer to
Component Inspection
INFOID:0000000000925055
INSPECTION PROCEDURE
1.
CHECK PARKING BRAKE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect parking brake switch connector.
26 – Ground
Parking brake ON
: Approx. 0 V
Parking brake OFF
: Approx. 5 V
26 – 1
: Continuity should exist.
26 – Ground
: Continuity should not exist.
Condition
Brake warning lamp illumination status
When the parking brake switch is opera-
tion
ON
When the parking brake switch is not oper-
ation.
OFF
BRC-48
< COMPONENT DIAGNOSIS >
[ABS]
PARKING BRAKE SWITCH
3.
Check continuity between parking brake switch terminal and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace parking brake switch.
Parking brake switch
—
Condition
Continuity
Connector
Terminal
M103
1
Ground
When the parking brake switch is operated.
Existed
When the parking brake switch is not operated.
Not existed
ABS WARNING LAMP
BRC-49
< COMPONENT DIAGNOSIS >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ABS WARNING LAMP
Description
INFOID:0000000000925060
×
: ON –: OFF
Component Function Check
INFOID:0000000000925061
1.
CHECK ABS WARNING LAMP OPERATION
Check that the lamp illuminates for approximately 1 second after the ignition switch is turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000000925062
1.
CHECK SELF-DIAGNOSIS
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check items displayed by self-diagnosis.
2.
CHECK COMBINATION METER
Check if the indication and operation of combination meter are normal. Refer to
.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit).
NO
>> Repair or replace combination meter.
Condition
ABS warning lamp
Ignition switch OFF
–
For 1 second after turning ON ignition switch
×
1 second later after turning ON ignition switch
–
ABS function is malfunctioning.
×
EBD function is malfunctioning.
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст