Nissan Qashqai (2007-2010). Manual — part 624
RING GEAR SHAFT
DLN-69
< DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
9.
Remove inner race of ring gear shaft bearing (adapter case
side) from ring gear with a drift (A) (commercial service tool) and
replacer.
M/T : Assembly
INFOID:0000000000972143
1.
Select ring gear adjusting shim (transfer case side). Refer to
2.
Assemble the selected ring gear adjusting shim (transfer case side) and outer races of ring gear shaft
bearing (transfer case side) to the transfer case.
CAUTION:
• Never reuse ring gear shaft bearing (transfer case side).
• Apply gear oil to the ring gear shaft bearing (transfer case side).
3.
Select ring gear adjusting shim (adapter case side). Refer to
4.
Install the selected ring gear adjusting shim (adapter case side) to the adapter case.
5.
Install outer race of ring gear shaft bearing (adapter case side)
to the adapter case with a drift (A) (commercial service tool).
CAUTION:
• Never reuse ring gear shaft bearing (adapter case side).
• Apply gear oil to the ring gear shaft bearing (adapter case
side).
6.
Install inner race of ring gear shaft bearing (adapter case side)
to the ring gear with drifts.
CAUTION:
• Never reuse ring gear shaft bearing (adapter case side).
• Apply gear oil to the ring gear shaft bearing (adapter case
side).
7.
Apply anti-corrosive oil to the spline of ring gear shaft. Install the
ring gear to ring gear shaft with drifts.
SDIA3083J
SDIA3102J
A
: Press adapter (If necessary)
B
: Drift (commercial service tool)
SDIA3097J
A
: Drift (SST: ST01530000)
B
: Drift (SST: ST35272000)
JSDIA0253ZZ
DLN-70
< DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY30A]
RING GEAR SHAFT
8.
Apply anti-corrosive oil to threads and seats of ring gear nut.
Tighten the ring gear nut with the specified torque by using a
torque wrench.
CAUTION:
• Never reuse ring gear nut.
• Never damage ring gear shaft.
9.
Install inner race of ring gear shaft bearing (transfer case side)
to the ring gear shaft with a drift (A) (SST: KV10111400).
CAUTION:
• Never reuse ring gear shaft bearing (transfer case side).
• Apply gear oil to the ring gear shaft bearing (transfer race
side).
10. Assemble the ring gear shaft assembly to the transfer case.
11. Install adapter case. Refer to
.
12. Check backlash, tooth contact, total preload and companion
flange runout. Refer to
.
CAUTION:
Measure the total preload without the adapter case oil seal.
13. Install adapter case oil seal (outer/inner) to the adapter case. Refer to
M/T : Inspection After Disassembly
INFOID:0000000000972144
Check items below. If necessary, replace them with new ones.
GEAR AND SHAFT
Check gear face and shaft for wear, cracks, damage, and seizure.
CAUTION:
Replace ring gear and drive pinion as a set (hypoid gear set) if any malfunction is detected on the ring
gear or drive pinion.
BEARING
Check for seizure, peeling, wear, corrosion, sticking, unusual noise, roughness in hand turning, and other
damage.
CAUTION:
Always replace inner race and outer race as a pair when replacing the bearing.
SHIM
Check for seizure, damage, and unusual wear.
CASE
Check the bearing mounting surface for wear, cracks and damages.
CVT
CVT : Exploded View
INFOID:0000000001060135
SDIA3100J
JSDIA0254ZZ
RING GEAR SHAFT
DLN-71
< DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
CVT : Disassembly
INFOID:0000000001070369
1.
Adapter case oil seal
2.
Adapter case
3.
O-ring
4.
Ring gear shaft
5.
Ring gear adjusting shim
(adapter case side)
6.
Ring gear shaft bearing
(adapter case side)
7.
Ring gear
8.
Ring gear nut
9.
Ring gear shaft bearing
(transfer case side)
10. Ring gear adjusting shim
(transfer case side)
11.
Transfer case
12. Air breather hose
13. Air breather tube
14. Gasket
15. Filler plug
16. Drain plug
17. Plug
18. Drive pinion
19. Drive pinion adjusting shim
20. Drive pinion bearing (front side)
21. Collapsible spacer
22. Drive pinion bearing (rear side)
23. Drive pinion oil seal
24. Companion flange
25. Lock nut
A: Oil seal lip
: Apply gear oil.
: Apply anti-corrosive oil.
: Apply Genuine Liquid Gasket, Three Bond TB1215 or equivalent.
Refer to
for symbols not described on the above.
JSDIA0211GB
DLN-72
< DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY30A]
RING GEAR SHAFT
1.
Remove adapter case. Refer to
.
2.
Remove adapter case oil seal from the adapter case. Refer to
.
3.
Tap the ring gear adjusting shim from the cutout on the adapter
case with a brass rod to remove ring gear shaft bearing outer
race (adapter case side) and ring gear adjusting shim (adapter
case side).
CAUTION:
Be careful not to damage adapter case.
4.
Remove ring gear shaft assembly from the transfer case.
5.
Remove outer race of ring gear shaft bearing (transfer case
side) and ring gear adjusting shim (transfer case side) from the
transfer case.
6.
Remove inner race of ring gear shaft bearing (transfer case
side) from ring gear shaft with drift (A) (commercial service tool)
and replacer (B) (SST: ST22730000).
7.
Remove ring gear nut (1).
CAUTION:
Never damage ring gear shaft.
8.
Remove ring gear from ring gear shaft with a drift (A) (SST:
ST33052000).
SDIA3079J
SDIA3080J
SDIA3081J
SDIA3082J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст