Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 392
CS-19
MT Gear Shift Lever
CONTROL SYSTEMS
2. EXCEPT FOR STI MODEL
NOTE:
• Clean all the parts before assembly.
• Apply NIGTIGHT LYW No. 2 grease or equiva-
lent to each part. <Ref. to CS-4, 5MT GEAR SHIFT
LEVER, COMPONENT, General Description.>
1) Mount the bushing and cushion rubber to the
stay.
2) Install the bushing and spacer to boss.
3) Using new self-locking nuts, install the boss to
the joint.
Tightening torque:
12 N·m (1.2 kgf-m, 8.9 ft-lb)
4) Install the snap ring to gear shift lever and install
the bushing.
NOTE:
Apply grease to the bushing.
5) Apply grease to the bushing and O-ring, and
then install to gear shift lever.
6) Apply sufficient grease into boss, and then install
the gear shift lever to the stay.
(A) Bushing
(B) Cushion rubber
(A) Bushing
(B) Spacer
CS-00061
(A)
(B)
CS-00238
(B)
(A)
(A)
CS-00322
(A) Spring pin
(B) Bushing
(C) Snap ring
(A) O-ring
(B) Bushing
CS-01414
(B)
(A)
(C)
CS-01415
(B)
(A)
(A)
CS-01413
CS-20
MT Gear Shift Lever
CONTROL SYSTEMS
7) Install the snap ring.
8) Insert the gear shift lever and rod into boot hole.
9) Install the rod.
Tightening torque:
12 N·m (1.2 kgf-m, 8.9 ft-lb)
10) Install a new lock wire.
NOTE:
• Install the lock wire to the stay groove.
• Bend the extra wire to the same direction of lock
wire winding.
(A) Snap ring
(A) Rod
(B) Lever
(C) Stay
CS-00318
(A)
CS-00317
(A)
(B)
(C)
(A) Lock wire
(A) Inner boot
(B) Lock wire
(C) Stay
CS-00316
(A)
CS-00240
(A)
(A)
(B)
(B)
B
B
(B)
B - B
(C)
CS-21
MT Gear Shift Lever
CONTROL SYSTEMS
E: INSPECTION
1) Check the parts (bushing, cushion rubber, spac-
er, boot, stay and rod, etc.) for deformation, dam-
age and wear. If necessary, correct or replace
faulty parts. Compare the removed parts with new
parts to judge if there are damages or not.
• STI model
• Except for STI model
(A) Bushing
(B) Cushion rubber
(C) Spacer
(D) Boot
(E) Stay
(F) Rod
CS-00921
(A)
(C)
(A)
(C)
(F)
(A)
(D)
(B)
(E)
(C)
(A) Bushing
(B) Cushion rubber
(C) Spacer
(D) Boot
(E) Stay
(F) Rod
CS-01045
(C)
(D)
(A)
(F)
(A)
(E)
(C)
(A)
(B)
(C)
CS-22
MT Gear Shift Lever
CONTROL SYSTEMS
2) Check the swing torque of rod linked with the
gear shift lever.
If the torque exceeds the specifications, replace the
bushing or retighten nuts.
Swing torque:
3.7 N (0.38 kgf, 0.83 lbf) or less
• STI model
• Except for STI model
(A) Pivot
(B) Swing torque
(A) Pivot
(B) Swing torque
CS-00116
(A)
(B)
CS-00116
(A)
(B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст