Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 693
GW-5
General Description
GLASS/WINDOWS/MIRRORS
4. REAR DOOR GLASS
(1)
Glass run rubber
(4)
Rear outer gusset cover
Tightening torque: N·m (kgf-m, ft-lb)
(2)
Glass
(5)
Regulator & motor ASSY
T: 7.5 (0.76, 5.5)
(3)
Weather strip outer
(6)
Door sash
GW-00751
(1)
(5)
T
(2)
(4)
T
T
(3)
T
T
T
(6)
GW-6
General Description
GLASS/WINDOWS/MIRRORS
5. MIRROR
B: CAUTION
• Before disassembling or reassembling parts, always disconnect the battery ground cable from battery.
When replacing the audio, control module and other parts provided with memory functions, record the mem-
ory contents before disconnecting the battery ground cable. Otherwise, the memory is cleared.
• Avoid impact and damage to the glass.
• Reassemble the parts in the reverse order of disassembly procedure unless otherwise indicated.
• Connect the connectors securely during reassembly.
• After reassembly, make sure that the functional parts operate normally.
(1)
Outer mirror case ASSY
(5)
Outer mirror lower cover
Tightening torque: N·m (kgf-m, ft-lb)
(2)
Mirror
(6)
Mount
T: 4.5 (0.46, 3.3)
(3)
Scalp cap
(7)
Spring
(4)
Side turn signal light ASSY
(8)
Rearview mirror ASSY
GW-00803
(4)
(1)
(2)
(6)
(7)
(8)
T
(5)
(3)
GW-7
General Description
GLASS/WINDOWS/MIRRORS
C: PREPARATION TOOL
1. SPECIAL TOOL
2. GENERAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
1B022XU0
SUBARU SELECT
MONITOR III KIT
Used for setting of each function and trouble-
shooting for electrical system.
TOOL NAME
REMARKS
Circuit tester
Used for measuring resistance and voltage.
Piano wire
Used for removing the window glass.
Cutter knife
Used for removing the window glass.
Windshield glass knife
Used for removing the window glass.
ST1B022XU0
GW-8
Power Window System
GLASS/WINDOWS/MIRRORS
2. Power Window System
A: WIRING DIAGRAM
Refer to “Power Window System” in the wiring diagram. <Ref. to WI-130, WIRING DIAGRAM, Power Win-
B: INSPECTION
1. RESET OPERATION A
1) Sit in the driver’s seat and close the door.
2) Turn the ignition switch to ON.
3) Operate the power window main switch to open the window glass halfway.
4) Operate the power window main switch to “UP” direction to fully close the driver’s side window glass.
5) While the window glass is fully closed, hold down the power window switch to “UP” direction for one sec-
ond.
6) Operate the power window main switch to “AUTO DOWN” direction to check whether the window fully
opens properly. If the window does not fully open properly, repeat steps 1) to 6).
2. RESET OPERATION B
1) Sit in the driver’s seat and close the door.
2) Turn the ignition switch to ON.
3) Perform “AUTO UP” operation for the driver’s side window glass, by fully pulling up the power window
main switch to cause the reverse operation (in reverse operation, the window is repeatedly fully closed and
then reversed to open it slightly) 10 times in row.
4) Check that the “AUTO UP” does not operate.
5) Perform reset operation A.
6) Check that the window operates properly by operating the “AUTO UP” and “AUTO DOWN” switch. If the
window does not fully open/close properly, repeat steps 1) to 6).
C: NOTE
For procedure of each component in the power window system, refer to the respective section.
• Power window control switch: <Ref. to GW-9, Power Window Control Switch.>
• Front door glass: <Ref. to GW-12, Front Door Glass.>
• Front regulator and motor assembly: <Ref. to GW-13, Front Regulator and Motor Assembly.>
• Rear door glass: <Ref. to GW-21, Rear Door Glass.>
• Rear regulator and motor assembly: <Ref. to GW-22, Rear Regulator and Motor Assembly.>
Symptoms
Repair order
All power windows do not operate.
1. Check the fuse (SBF-4).
2. Check the power window circuit breaker.
3. Check the power window relay.
4. Check the wiring harness.
Particular window does not operate.
1. Check the power window main switch.
2. Check the power window sub-switch.
3. Check the power window motor.
4. Check the wiring harness.
“Window Lock” does not operate.
Check the power window main switch.
Driver’s side window moves slightly (approx. 20 mm (0.79 in)).
1. Check the power window motor.
2. Check the power window main switch.
3. Check the wiring harness.
Driver’s side window moves slightly (approx. 50 mm (1.97 in)).
(This status is not a failure.)
Perform reset operation A. <Ref. to GW-8, RESET OPERA-
TION A, INSPECTION, Power Window System.>
Driver’s side window does not close completely. (Using AUTO
UP allows the window to fully close first and then move in
reverse resulting in slightly opening.)
Perform reset operation B. <Ref. to GW-8, RESET OPERA-
TION B, INSPECTION, Power Window System.>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст