Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 14
PI-10
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
• Passenger’s side
Alarm sound operational check
• The system uses the buzzer and sounds the
alarm when the door is locked or unlocked. The
alarm sound can be turned OFF. To turn the alarm
sound from ON to OFF, close all doors, (with the
key not inserted in the key cylinder), hold down the
“UNLOCK” side of the power door lock switch and
insert the key in the key cylinder. Within 10 sec-
onds, insert and take out the key for 5 times or
more, and within 10 seconds after that, open and
close the driver’s door. With the door closed, the
hazard light will flash 3 times, indicating that the
alarm sound has been turned OFF. To turn the
alarm sound from OFF to ON, perform this proce-
dure again. The hazard light will flash 3 times, indi-
cating that the alarm has been turned ON.
21.SECURITY SYSTEM
Check that the security system operates as indicat-
ed below.
1) Fully open all the door windows.
2) Remove the key from the ignition switch and
close all the doors including rear gate.
3) Press the “LOCK/ARM” button on the keyless
transmitter once.
4) If all doors lock, and the security display light
flashes as indicated below, the alarm system is in
the monitoring prepared condition.
• Alarm system monitoring prepared condition
5) Check that the system enters monitoring condi-
tion 30 seconds after the condition in 4).
• Alarm system monitoring condition (all models)
PI-00722
PI-00357
(A) Light ON
(B) Light OFF
(C) 2 seconds
(A) Light ON
(B) Light OFF
(C) 2 seconds
PI-00504
PI-00315
(A)
(B)
(C)
(A)
(B)
(C)
PI-00265
PI-11
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
6) Press the “UNLOCK/DISARM” button on the
keyless transmitter once.
7) If the driver’s door is unlocked, and the security
display light flashes as indicated below, the alarm
system is in the non-monitoring condition.
• Alarm system non-monitoring condition
8) Press the “LOCK/ARM” button once on the key-
less transmitter with one of the doors (including the
rear gate) opened.
9) Check that the buzzer sounds 5 times to give the
door not fully closed warning.
10) Close all the doors including rear gate.
11) Check that the alarm system is in the monitor-
ing prepared condition (all the doors lock).
• Alarm system monitoring prepared condition
12) Check that the system enters monitoring condi-
tion 30 seconds after the condition in 11).
13) Press the “UNLOCK/DISARM” button on the
keyless transmitter once and turn into non-monitor-
ing condition.
(A) Light ON
(B) Light OFF
(C) 3 seconds
PI-00358
PI-00504
(A)
(B)
(C)
PI-00266
PI-00357
(A) Light ON
(B) Light OFF
(C) 2 seconds
(A) Light ON
(B) Light OFF
(C) 2 seconds
PI-00315
(A)
(B)
(C)
(A)
(B)
(C)
PI-00265
PI-00358
PI-12
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
14) With one of all the doors open (including the
rear gate), press the “LOCK” side of the power door
lock switch.
• Driver’s side
• Passenger’s side
15) Close all the doors including rear gate.
16) All the doors are locked and the alarm system
is in the monitoring prepared condition.
• Alarm system monitoring prepared condition
17) Check that the system enters monitoring condi-
tion 30 seconds after the condition in 16).
18) When the alarm system is in the monitoring
condition, use the inner lock knob or the key to un-
lock the door, and open the door.
19) Check that the alarm condition occurs (horn
sounds continuously, hazard light flashes, security
indicator illuminates).
20) Check that the condition in 19) continues for 30
seconds or more, or until the “UNLOCK/DISARM”
button of the keyless transmitter is pressed, or until
the ignition switch is turned ON with the correct ig-
nition key.
21) On models equipped with an impact sensor, hit
the windshield glass with your hand with the alarm
system in the monitoring condition, to check that
the alarm condition occurs.
22) When none of above is applicable, perform
troubleshooting for the security system. <Ref. to
SL-26, INSPECTION, Security System.>
22.SEAT
1) Check that each seat provides full functionality in
sliding and reclining. Check all available functions
of the rear seat such as a trunk-through center arm-
rest.
2) Check the passenger’s seat occupant detection
system.
(1) Empty the passenger’s seat and turn the ig-
nition switch to ON.
(A) Light ON
(B) Light OFF
(C) 2 seconds
PI-00720
PI-00722
PI-00315
(A)
(B)
(C)
(A) Light ON
(B) Light OFF
(C) 2 seconds
(A)
(B)
(C)
PI-00265
PI-13
Pre-delivery Inspection
PRE-DELIVERY INSPECTION
(2) Check that the passenger airbag ON/OFF
indicator lights both turn on simultaneously for
approximately six seconds, and after turning off
for two seconds, only the OFF light illuminates.
3) With a person weighing approximately 70 kg
(155 lb) or more sitting in the passenger’s seat,
check whether the ON light of the passenger’s air-
bag ON/OFF indicator illuminates or not.
4) Have the passenger get out of the passenger’s
seat, and check whether the OFF light of the pas-
senger side airbag ON/OFF indicator illuminates.
23.SEAT BELT
1) Pull out the seat belt and then release it. Check
that the belt retracts smoothly.
2) Check seat warning system
(1) Turn the ignition switch to ON without driv-
er’s and passenger’s seat belts on.
(2) Check the seat belt warning lights of the
driver’s and the passenger’s blink for approxi-
mately six seconds and the buzzer sounds in-
termittently.
(3) Then check that the seat belt warning lights
illuminate and blink in a cycle of approximately
15 seconds. (If no one is seated on the passen-
ger’s seat, the seat belt warning light of the pas-
senger’s will not operate.)
24.TPMS (U.S. MODELS ONLY)
1) Turn the ignition switch to ON, and check that
the TPMS warning light is in a normal operation
condition.
• Normal operation (IG ON (Light check))
2) If the TPMS warning light display does not oper-
ate normally, check and repair the system. <Ref. to
TPM(diag)-2, Basic Diagnostic Procedure.>
25.ECM PROTECTOR
For Canada model, check the ECM protector instal-
lation conditions. Make sure that the special nut
and the plastic cover of ECM protector are securely
installed.
(A) Airbag ON/OFF indicator light (U.S. model)
(B) Airbag ON/OFF indicator light (Canada, Mexico
model)
(B)
(B)
(B)
(A)
PI-00450
(A) ECM protector
(B) Special nut
(C) Plastic cover
2s
IGN ON
ON
OFF
PI-00376
(B)
(B)
(C)
(A)
PI-00453
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст