Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 777
LAN(diag)-17
Subaru Select Monitor
LAN SYSTEM (DIAGNOSTICS)
Blower fan information
ON/OFF
CAN data input value
ON when blower fan is operating (always OFF for
auto A/C equipped models)
Smart judging flag
Smart System/Other
than Smart System
CAN data output value
Smart when integrated unit judges as a model
with Smart
Diesel judging flag
Diesel/Other than
Diesel
CAN data output value Display diesel/other than diesel
Turbo judging flag
Without turbo/TURBO CAN data output value Display engine equipped
AT type judging flag
4AT/5AT
CAN data output value Display transmission equipped
CVT judging flag
CVT/Other than CVT
CAN data output value Display CVT judging
Center display failure
OK/NG
CAN data input value
NG when there is a center display failure
Reception from center display (NAVI monitor)
NAVI Failure
OK/NG
CAN data input value
NG when there is a navigation system failure
Reception from Center Display
IE Bus failure
Can not use
CAN data input value
Reception from Center Display
Auto A/C failure
OK/NG
CAN data input value
NG when there is a failure in auto air conditioning
system
Reception from auto A/C module
EBD Warning Light
ON/OFF
CAN data input value
OK when EBD warning light is illuminated
Reception from VDC/ABS and transmission to
combination meter
ABS Warning Light
ON/OFF
CAN data input value
OK when ABS warning light is illuminated
Reception from VDC/ABS and transmission to
combination meter
VDC OFF flag
ON/OFF
CAN data input value
Vehicle dynamics control OFF SW is ON
Reception from VDC/ABS and transmission to
combination meter
VDC/ABS OK B
OK/NG
CAN data input value
NG when there is an error in VDC/ABS system
Reception from VDC/ABS
Lighting I Switch Input
ON/OFF
Body integrated unit
input value
ON when lighting switch illumination is ON
Lighting II Switch Input
ON/OFF
Body integrated unit
input value
ON when lighting switch headlight is ON
Dimmer Hi Switch Input
ON/OFF
Body integrated unit
input value
ON when dimmer switch is Hi beam position
Dimmer Pass Switch Input
ON/OFF
Body integrated unit
input value
ON when dimmer switch is passing position
Lighting I Lamp Output
ON/OFF
Body integrated unit
output value
ON when small light is illuminated
Lighting II Lamp Output
ON/OFF
Body integrated unit
output value
ON when headlight is illuminated
Lighting Hi Lamp Output
ON/OFF
Body integrated unit
output value
ON when Hi beam is illuminated
Front Fog Lamp Output
ON/OFF
Body integrated unit
output value
ON when front fog light is ON.
DRL Cancel Output
ON/OFF
Body integrated unit
output value
ON when lighting switch is “Headlight ON” and
dimmer switch is “Hi beam” or “Passing” position
Power Supply Tr
ON/OFF
Body integrated unit
output value
ON when lighting switch is “Head” position without
inserting key in key cylinder
Spot map lamp output
ON/OFF
Body integrated unit
output value
ON when one of the doors is open (except for tail
gate)
Eco switch information
ON/OFF
CAN data output value Not applicable
Off delay time
OFF, Short, Normal,
Long
Body integrated unit
setting items
Customize setting
Check engine warning
lamp output
ON, OFF, Blink 1,
Blink 2, Blink 3
Body integrated unit
output value
Warning light is activated
Items to be displayed
Unit of measure
Remarks
Note
LAN(diag)-18
Subaru Select Monitor
LAN SYSTEM (DIAGNOSTICS)
NOTE:
For detailed operation procedures, refer to “PC application help for Subaru Select Monitor”.
Rr defogger op. mode
Continuous/Normal
Body integrated unit
setting items
Customize setting
Security Alarm Setup
ON/OFF
Body integrated unit
setting items
Customize setting
Impact Sensor Setup
ON/OFF
Body integrated unit
setting items
Customize setting
Alarm delay setup
ON/OFF
Body integrated unit
setting items
Customize setting
Lockout prevention
ON/OFF
Body integrated unit
setting items
Customize setting
Impact sensor
ON/OFF
Body integrated unit
setting items
Customize setting
Buzzer beeping setup
ON/OFF
Body integrated unit
setting items
Customize setting
Hazard light setup
ON/OFF
Body integrated unit
setting items
Customize setting
Buzzer setting
ON/OFF
Body integrated unit
setting items
Inside condition of unit
Auto locking
ON/OFF
Body integrated unit
setting items
Customize setting
Passive Alarm
ON/OFF
Body integrated unit
setting items
Customize setting
Door open warning
ON/OFF
Body integrated unit
setting items
Customize setting
Dome Light Alarm Setting
ON/OFF
Body integrated unit
setting items
Customize setting
Map Light Setting
ON/OFF
Body integrated unit
setting items
Customize setting
Belt Warning Switch
ON/OFF
Body integrated unit
setting items
Customize setting
Map lamp 30 sec off record
ON/OFF
Body integrated unit
setting items
Customize setting
A/C ECM setting
ON/OFF
Body integrated unit
setting items
Equipment setting
wiperdeicer
ON/OFF
Body integrated unit
setting items
Equipment setting
Sedan/Wagon Setting
Sedan/Wagon
Body integrated unit
setting items
Equipment setting
MT/AT Setting
MT/AT
Body integrated unit
setting items
Equipment setting
6MT Setting
6MT/Other than 6MT
Body integrated unit
setting items
Equipment setting
Destination Setting
Each destination
Body integrated unit
setting items
—
Factory initial setting
Factory/Market
Body integrated unit
setting items
Equipment setting
Items to be displayed
Unit of measure
Remarks
Note
LAN(diag)-19
Subaru Select Monitor
LAN SYSTEM (DIAGNOSTICS)
4. CONFIRM CURRENT SETTING
1) On «Main Menu» display, select {Each System Check}.
2) On «System Selection Menu» display, select {Integ. unit mode}.
3) On «Integ. unit mode failure diag.» display, select {Current Data Display & Save}.
4) Using the scroll key, scroll the display screen up or down until the desired data is shown.
5) Display the following item and record the settings.
Required items for new registration (Except for system not equipped)
Item
Item to confirm
Remarks
number of regist.
1
2
3
4
Number of registered key
Off delay time
OFF
Long
Normal
Short
Setting for lighting off time
Rr Defogger op. mode
Normal
Continuous
Security Alarm Setup
ON
OFF
Impact Sensor Setup
ON
OFF
Option setting
Alarm delay setup
ON
OFF
Lockout prevention
ON
OFF
Impact sensor
support
no support
Option setting
Buzzer beeping setup
ON
OFF
Emergency light setup
ON
OFF
Buzzer setting
support
no support
Passive Alarm
ON
OFF
Door open warning
support
no support
Dome Light Alarm Setting
ON
OFF
Map Light Setting
ON
OFF
Belt Warning Switch
ON
OFF
Switch the belt warning lighting
and the buzzer sound.
Map lamp 30 sec off record
support
no support
A/C ECM setting
support
no support
Model with auto A/C
wiperdeicer
support
no support
Option setting
Sedan/Wagon Setting
Sedan
Wagon
MT/AT Setting
AT
MT
6MT Setting
6MT
Other than 6MT
Factory initial setting
Factory
Market
Do not change to factory mode.
LAN(diag)-20
Subaru Select Monitor
LAN SYSTEM (DIAGNOSTICS)
5. REGISTRATION BODY INTEGRATED
UNIT (FUNCTION SETTING)
CAUTION:
Body integrated unit is core of LAN system, and
also can select the function of all vehicle sys-
tem control. It is possible to control the original
functions of vehicle when registrations of body
integrated unit, or User Customizing are corre-
sponded to vehicle equipment.
If registrations and function setting are differ-
ent from vehicle equipment, vehicle system
does not operate normally and diagnosis can-
not be performed correctly. Pay attention to fol-
lowing item.
• Be sure to correspond registrations, or User
Customizing settings to vehicle equipment.
• Do not change the settings of vehicle improp-
erly.
• Confirm that key illumination does not blink
when ignition switch is turned ON, or “Factory
initial setting” of body integrated unit registra-
tions is set to “Market”. If “Factory initial set-
ting” is set to “Factory”, key illumination blinks
when the ignition switch is turned ON, to notify
that the settings are not confirmed.
• Key illumination does not blink with ignition
switch turned to ON and go off with door
closed.
• Be sure to register immobilizer if body inte-
grated unit is replaced with a new part or if the
parts related to immobilizer have been re-
placed. Refer to the “REGISTRATION MANUAL
FOR IMMOBILIZER”.
1) Connect SDI to data link connector located in the
lower portion of the instrument panel (on the driv-
er’s side).
CAUTION:
Do not connect scan tools other than the Suba-
ru Select Monitor.
2) Start the PC.
3) Turn the ignition switch to ON and run the “PC
application for Subaru Select Monitor”.
4) On «Main Menu» display, select {Each System
Check}.
5) On «System Selection Menu» display, select {In-
teg. unit mode}.
6) Click the [OK] button after the control module
name (integrated unit) is displayed.
7) On «Integ. unit mode failure diag.» display, se-
lect {Unit customizing}.
CC-00653
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст