Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 755
EB-31
Rear Gate
EXTERIOR BODY PANELS
2. REAR GATE DAMPER STAY
CAUTION:
• Do not damage piston rods and oil seals.
• Never disassemble cylinders: They contain
gas.
• Rear gate panels are heavy. When removing
and installing them, always work in a team of
two or more persons.
1) Before removing the rear gate damper stay, pre-
vent the rear gate from closing using prop or the
like.
CAUTION:
If the prop comes off, operators may get injured
and vehicle may get damaged. Make sure to
support the rear gate with secure material to
prevent injury or damage.
2) Remove the mounting bolt of rear gate damper
stay.
3) Remove mounting bolt, and remove the damper
stay.
B: INSTALLATION
1. REAR GATE PANEL
CAUTION:
Rear gate panels are heavy. When removing
and installing them, always work in a team of
two or more persons.
1) Install each part in the reverse order of removal.
Tightening torque:
25 N·m (2.55 kgf-m, 18.4 ft-lb)
2) Install while paying attention to make a uniform
clearance around the rear gate panel. For the di-
mension of clearance, refer to “SPECIFICATION”
in “General Description”. <Ref. to EB-2, SPECIFI-
2. REAR GATE DAMPER STAY
CAUTION:
Rear gate panels are heavy. When removing
and installing them, always work in a team of
two or more persons.
1) Prevent the rear gate from closing using prop or
the like.
CAUTION:
If the prop comes off, operators may get injured
and vehicle may get damaged. Make sure to
support the rear gate with secure material to
prevent injury or damage.
2) Install each part in the reverse order of removal.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. <Ref. to EB-12, REAR GATE, COMPO-
EB-00389
EB-00282
EB-00382
EB-00389
EB-32
Rear Gate
EXTERIOR BODY PANELS
C: ADJUSTMENT
For the dimension of panel around the rear gate
panel, refer to “SPECIFICATION” in “General De-
scription”. <Ref. to EB-2, SPECIFICATION, Gener-
1) Align the rear gate panel longitudinal and lateral
position.
(1) Loosen the hinge attaching bolts.
(2) Align the rear gate panel longitudinal and
lateral panel dimension.
2) Adjust the gap between rear gate panel and
body surface.
(1) Loosen the bolt.
(2) Tap striker using plastic hammer to adjust
the gap between rear gate panel and body sur-
face.
D: DISPOSAL
1. REAR GATE DAMPER STAY
CAUTION:
Gas is colorless, odorless, and harmless. How-
ever, gas pressure may spray cutting powder or
oil. Be sure to wear dust-resistant goggles.
1) Cover with a vinyl sack as shown in the figure.
NOTE:
Prevent the vinyl sack from being caught by drill
cutting edge.
2) Lift the body side slightly with piston rods fully
extended, and secure the body side with vise.
Drill a hole of 2 to 3 mm (0.08 to 0.12 in) diameter
at a point 10 to 200 mm (0.39 to 7.87 in) from the
body side, and bleed the gas in the rear gate damp-
er stay completely.
EB-00023
EB-00480
(1) Rear gate damper stay
(2) Vinyl sack
(1) Door side
(2) Body side
(3) 190 mm (7.48 in)
(4) 10 mm (0.39 in)
(5) Piston rod
(6) Cylinder
(7) Portion to be drilled
EB-00031
(1)
(2)
EB-00032
(3)
(4)
(1)
(5)
(6)
(7)
(2)
EB-33
Trunk Lid
EXTERIOR BODY PANELS
11.Trunk Lid
A: REMOVAL
1. TORSION BAR
1) Open the trunk lid.
2) Using the ST, remove the torsion bar from the
hinge link.
CAUTION:
During removal and installation, handle the tor-
sion bar carefully, because it will generate reac-
tive force.
Preparation tool: REMOVER (927780000)
3) Remove the torsion bars RH/LH.
2. TRUNK LID ARM
1) Disconnect the ground cable from battery.
2) Open the trunk lid to remove the trunk room trim.
<Ref. to EI-63, REMOVAL, Trunk Room Trim.>
3) Disconnect the trunk lid release cable. <Ref. to
SL-38, REMOVAL, Trunk Lid Latch and Actuator
4) Disconnect the connectors, and remove the har-
ness clip, etc.
5) Remove the trunk lid mounting bolts, to remove
the trunk lid panel from the trunk lid arm.
6) Remove the torsion bar from the trunk lid hinge
link. <Ref. to EB-33, TORSION BAR, REMOVAL,
7) Remove the rear shelf trim. <Ref. to EI-62, RE-
8) Remove the bolts, then remove the trunk lid arm.
3. TRUNK LID PANEL
1) Disconnect the ground cable from battery.
2) Disconnect the connector to remove the trunk lid
harness.
3) Detach the rear spoiler.
• Small type: <Ref. to EI-42, SMALL TYPE, RE-
• Large type: <Ref. to EI-42, LARGE TYPE, RE-
MOVAL, Rear Spoiler.>
CAUTION:
The trunk panel become lighter after removing
the rear spoiler, so be careful when opening/
closing the trunk lid.
4) Remove the trunk lid latch and actuator assem-
bly. <Ref. to SL-38, REMOVAL, Trunk Lid Latch
5) Remove the trunk lid garnish. <Ref. to EI-73,
6) Remove the bolts, then remove the trunk lid pan-
el from the trunk lid arm.
ST
EB-00067
EB-00066
EB-00157
EB-00066
EB-34
Trunk Lid
EXTERIOR BODY PANELS
B: INSTALLATION
1) Install each part in the reverse order of removal.
CAUTION:
Make sure that the harness grommet for the li-
cense plate light is securely installed on the ve-
hicle. If not properly installed, this may cause
water leakage.
2) Apply grease to the rotating area of hinges and
the torsion bar.
3) Install while paying attention to make a uniform
clearance around the trunk lid panel. For the di-
mension of clearance, refer to “SPECIFICATION”
in “General Description”. <Ref. to EB-2, SPECIFI-
CATION, General Description.>
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. <Ref. to EB-13, TRUNK LID PANEL,
COMPONENT, General Description.>
C: ADJUSTMENT
For the dimension of panel around the trunk lid
panel, refer to “SPECIFICATION” in “General De-
scription”. <Ref. to EB-2, SPECIFICATION, Gener-
1) Adjust the trunk lid panel lateral position.
(1) Loosen the mounting bolt.
(2) Align the trunk lid panel lateral panel dimen-
sion.
2) Adjust the gap between trunk lid panel and body
surface.
(1) Loosen the bolt.
(2) Tap striker using plastic hammer to adjust the
gap between trunk lid panel and body surface.
EB-00066
EB-00488
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст