Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 723
SL-41
Remote Openers
SECURITY AND LOCKS
3. FUEL FILLER LID OPENER
5 door model
1) Remove the rear seat. <Ref. to SE-13, REMOV-
2) Remove the lower inner trim, rear quarter trim
and floor mat on the driver’s side. Remove the clip
holding the cable.
3) Remove the opener lever and detach the cover.
4) Remove the bolts, then remove the pull handle
assembly.
5) Remove the cable from pull handle assembly.
6) Rotate the fuel lock inside the quarter panel to
90° and remove. (Either right or left turn)
4 door model
Refer to the trunk lid opener. <Ref. to SL-40,
TRUNK LID OPENER, REMOVAL, Remote Open-
B: INSTALLATION
Install each part in the reverse order of removal.
C: INSPECTION
Check if the front hood, trunk lid and fuel flap oper-
ate normally.
(1) Cover
(2) Pull handle ASSY
(3) Cable
(4) Opener lever
SL-01559
(2)
(1)
(3)
(4)
SL-00265
SL-42
Ignition Key Lock
SECURITY AND LOCKS
16.Ignition Key Lock
A: REPLACEMENT
1) Disconnect the ground cable from battery.
2) Remove the steering column. <Ref. to PS-16,
3) Secure the steering column in a vise. Remove
the bolt with a drill.
CAUTION:
Do not apply any impact to the set bolt by a
chisel or punch.
4) Remove the ignition key lock.
5) Use new bolts. Tighten the bolt until the bolt
head is broken (bolt head wrenched off).
B: INSPECTION
1) Remove the instrument panel lower cover.
2) Remove the lower column cover.
3) Unfasten the fixing clip which secures harness,
and then disconnect the connector of the ignition
switch from body harness.
4) Turn the ignition key plate to each position and
check the resistance between ignition connector
terminals.
5) Replace the ignition switch if the inspection re-
sult is not within the standard value.
SL-00024
SL-00876
Switch position
Terminal No.
Standard
LOCK
—
—
ACC
3 and 5
Less than 1 Ω
ON
3 and 1 and 4
3 and 5
Less than 1 Ω
ST
3 and 2
3 and 1 and 6
Less than 1 Ω
SL-00266
1
3
4
5
6
2
SL-43
Key Lock Cylinders
SECURITY AND LOCKS
17.Key Lock Cylinders
A: REPLACEMENT
1. FRONT DOOR
1) Raise the front door glass to the top position.
2) Remove the front door trim. <Ref. to EI-45, RE-
3) Remove the sealing cover. <Ref. to EB-21, RE-
4) Remove the rod clamp.
5) Remove the plug to the rear of the door panel.
6) Loosen TORX
®
bolt (1).
7) Remove the key cylinder along with the handle
cover.
8) Remove the key cylinder from the cover, and re-
place the key cylinder.
2. GLOVE BOX LID
1) Remove the glove box damper.
2) Remove the stoppers and pull the glove box lid
assembly forward to remove.
3) Pull up the lock knob with the key cylinder in UN-
LOCK.
4) Insert the key while holding the condition of step
3), and pull out the key in LOCK status.
5) Remove the key cylinder from lock knob while
pushing in the metal plate, and replace the key cyl-
inder.
(1) Latch connection rod
(2) Key cylinder
(3) Door outer handle cover
SL-00887
(1)
(1)
SL-00801
(1)
(2)
(3)
EI-01887
EI-01831
SL-01251
SL-01252
SL-01253
SL-44
Security Control Module
SECURITY AND LOCKS
18.Security Control Module
A: NOTE
The control of security system is carried out in body
integrated unit. Refer to the section on the body in-
tegrated unit for the work procedures.
• Removal: <Ref. to SL-48, REMOVAL, Body Inte-
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст