Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 474
RS-3
General Description
REAR SUSPENSION
B: COMPONENT
1. REAR SUSPENSION
(1)
Shock absorber
(13) Front lateral link bushing
Tightening torque:N·m (kgf-m, ft-lb)
(2)
Self-locking nut
(14) Snap pin
T1: 30 (3.1, 22.1)
(3)
Rear stabilizer
(15) Front sub frame support plate
T2: 38 (3.9, 28)
(4)
Stabilizer bushing
(16) Rear sub frame
T3: 60 (6.1, 44.3)
(5)
Stabilizer clamp
(17) Rear sub frame stopper plate
(lower)
T4: 70 (7.1, 51.6)
(6)
Stabilizer link
(18) Adjusting bolt
T5: 80 (8.2, 59)
(7)
Rear lateral link
(19) Adjusting washer
T6: 90 (9.2, 66.4)
(8)
Rear housing
(20) Rear lateral link bushing
T7: 100 (10.2, 73.8)
(9)
Upper arm
(21) Flange nut
T8: 145 (14.8, 106.9)
(10) Trailing link
(22) Rear sub frame stopper plate
(upper)
(11) Trailing link bushing
(23) Rear housing bushing
(12) Front lateral link
(24) Bolt
(21)
(3)
(4)
(5)
(16)
(17)
(15)
T4
T6
T5
T6
T8
T8
T1
T2
T2
(1)
(2)
T1
(2)
T5
(18)
(12)
(14)
(19)
(13)
T3
T7
(2)
(11)
(10)
(20)
(6)
(8)
(21)
(2)
(2)
T6
T6
(21)
T5
(2)
(2)
(9)
(7)
(17)
T8
RS-00383
T5
(22)
(22)
(23)
(2)
(24)
(24)
(24)
(24)
(24)
(2)
(24)
RS-4
General Description
REAR SUSPENSION
2. SHOCK ABSORBER
(1)
Mount
(5)
Shock absorber
Tightening torque: N·m (kgf-m, ft-lb)
(2)
Upper rubber sheet
(6)
Self-locking nut
T: 25 (2.5, 18.4)
(3)
Dust cover
(7)
Helper
(4)
Coil spring
(4)
(5)
(6)
(3)
(7)
(2)
(1)
T
RS-00286
RS-5
General Description
REAR SUSPENSION
C: CAUTION
Please clearly understand and adhere to the following general precautions. They must be strictly followed to
avoid minor or serious injury to the person doing the work or people in the area.
1. CAUTIONS
• Wear appropriate work clothing, including a cap, protective goggles and protective shoes when performing
any work.
• Before disposing of shock absorbers, be sure to bleed the gas out completely. Also, do not expose to
flames or fire.
• Before removal, installation or disassembly, be sure to clarify the failure. Avoid unnecessary removal, in-
stallation, disassembly and replacement.
• Use SUBARU genuine grease etc. or equivalent. Do not mix grease etc. of different grades or manufac-
turers.
• Before securing a part on a vise, place cushioning material such as wood blocks, aluminum plate, or cloth
between the part and the vise.
• Be sure to tighten fasteners including bolts and nuts to the specified torque.
• Place shop jacks or rigid racks at the specified points.
2. OIL
When handling oil, adhere to the following to prevent unexpected accident.
• Prepare container and waste cloths when performing work which oil could possibly spill. If oil spills, wipe
it off immediately to prevent from penetrating into floor or flowing outside, for environmental protection.
• Follow all government regulations concerning disposal of refuse when disposing.
D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
20099AE000
INSTALLER &
REMOVER
Used for replacing the front lateral link bushing.
499755602
PRESS
Used for replacing the rear trailing link bushing.
ST20099AE000
ST-499755602
RS-6
General Description
REAR SUSPENSION
20099AE010
INSTALLER &
REMOVER
Used for replacing the rear lateral link bushing.
20299AG010
BASE
Used for replacing the rear trailing link bushing.
899874100
INSTALLER
Used for replacing the rear trailing link bushing.
20399FG000
STRUT MOUNT
SOCKET
• Used for removing and installing shock mount.
• Used for checking torque of shock mount cen-
ter nut.
28099PA090
OIL SEAL PROTEC-
TOR
• Used for installing the rear drive shaft to the
rear differential.
• For oil seal protection
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST20099AE010
ST20299AG010
ST-899874100
ST20399FG000
ST28099PA090
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст