Subaru Legacy (2005 year). Service manual — part 882
AB-3
AIRBAG SYSTEM
General Description
6. FRONT SUB SENSOR
Tightening torque:
13 N
⋅
m (1.32 kgf-m, 9.6 ft-lb)
CAUTION:
Do not reuse mounting bolts and nuts.
7. SIDE AIRBAG SENSOR
Tightening torque:
7.4 N
⋅
m (0.75 kgf-m, 5.5 ft-lb)
CAUTION:
Do not reuse mounting bolts and nuts.
8. CURTAIN AIRBAG SENSOR
Tightening torque:
7.4 N
⋅
m (0.75 kgf-m, 5.5 ft-lb)
CAUTION:
Do not reuse mounting bolts and nuts.
9. STEERING ROLL CONNECTOR
(A) Bolt
(A) Nut
AB-01189
T
T
(A)
(A)
AB-01190
T
(A)
(A) Nut
AB-01191
(A)
AB-00756
AB-4
AIRBAG SYSTEM
General Description
10.AIRBAG HARNESS
(1)
Airbag main harness
(2)
Airbag rear harness
AB-00757
(1)
(2)
AB-5
AIRBAG SYSTEM
General Description
B: CAUTION
• When servicing a vehicle, be sure to turn the ig-
nition switch to OFF, disconnect the ground cable
from battery, and wait for more than 20 seconds
before starting work.
• The airbag system is fitted with a backup power
source. If the airbag system is serviced within 20
seconds after the ground cable is disconnected, it
may inflate.
• If the airbag warning light illuminates, repair the
vehicle immediately. Airbag or pretensioner may in-
flate incorrectly, or not inflate in collision.
• If sensors, airbag module, airbag control module,
pretensioner and harness are deformed or dam-
aged, replace them with new parts.
• When checking the airbag system, be sure to
use a digital circuit tester. Use of an analog circuit
tester may cause the airbag to activate erroneous-
ly.
• When checking, use a test harness (1). Since
damage to the connector terminal may cause the
airbag to activate erroneously, do not directly apply
the tester probe to any connector terminal of the
airbag.
• Do not check continuity of the airbag modules for
driver’s side, passenger’s side and curtain, or pre-
tensioner.
AB-00120
AB-00121
AB-00122
(1)
AB-00006
AB-6
AIRBAG SYSTEM
General Description
• Do not drop the airbag module, subject them to
high temperature over 93
°C (199°F), or let water,
oil or grease get on them; the internal parts may be
damaged and reliability greatly lowered.
• If any damage, opening or rust is found on the
airbag system wire harness, do not attempt to re-
pair using soldering equipment. Replace the faulty
harness with a new genuine part.
• Install the wire harness securely with the speci-
fied clips to avoid interference or tangled up with
other parts.
• Do not allow water or oil to come in contact with
the connector terminals. Also do not touch the con-
nector terminals.
• Either of the airbag modules for driver’s, passen-
ger’s, side or curtain, or pretensioner must not be
disassembled.
• The removed front seat with an airbag module
must be kept at least 200 mm (8 in) away from walls
and other objects.
• Do not use the airbag parts or pretensioner parts
of other vehicles. Always replace the defective
parts with new parts.
• Never reuse deployed airbag and pretensioner.
• When painting or performing sheet metal work
on the front part of the vehicle, including the front
wheel apron, front fender and front side frame, re-
move the front sub sensors and wire harness of air-
bag system.
• Do not discard a undeployed airbag module or
pretensioner.
AB-00123
AB-00124
AB-00125
(1) 200 mm (8 in) or more
AB-00126
AB-00779
AB-00128
(1)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст