Subaru Legacy IV (2008 year). Service manual — part 659
CS-43
MT Gear Shift Lever
CONTROL SYSTEMS
8) Install the rear exhaust pipe and muffler.
• SOHC model
<Ref. to EX(H4SO)-8, INSTALLATION, Rear Ex-
haust Pipe.> <Ref. to EX(H4SO)-10, INSTALLA-
TION, Muffler.>
• DOHC turbo model
<Ref. to EX(H4DOTC)-13, INSTALLATION, Rear
Exhaust Pipe.> <Ref. to EX(H4DOTC)-14, IN-
STALLATION, Muffler.>
9) Install the plate assembly to the vehicle body.
Tightening torque:
18 N·m (1.8 kgf-m, 13.3 ft-lb)
(1) Set the plate assembly to the vehicle.
(2) Temporarily tighten the bolt (A).
(3) Tighten the bolt (B).
(4) Tighten the bolt (A).
(5) Tighten the bolts (C) and (D).
10) Install the harness clamp to the plate.
11) Install the boot and insulator assembly, and se-
cure with a clamp.
12) Install the front cover assembly.
13) Install the console box. <Ref. to EI-54, INSTAL-
LATION, Console Box.>
14) Install the shift knob.
15) Check that the gear can be shifted accurately
into each gear ranges.
2. 6MT MODEL
1) Insert the gear shift lever from the room side.
NOTE:
Insert the rod and the stay, and position the lever
on top of the transmission mount.
2) Mount the cushion rubber on the vehicle body.
Tightening torque:
18 N·m (1.8 kgf-m, 13.3 ft-lb)
3) Move the transmission to the right side of the ve-
hicle, and attach the joint COMPL and stay.
Tightening torque:
T1: 12 N·m (1.2 kgf-m, 8.9 ft-lb)
T2: 32 N·m (3.3 kgf-m, 23.6 ft-lb)
4) Install the crossmember. <Ref. to 6MT-30, IN-
STALLATION, Transmission Mounting System.>
CS-00314
(B)
(A)
(C)
(D)
CS-00312
(A) Reverse check cable
CS-00222
CS-00223
(A)
T1
T2
CS-44
MT Gear Shift Lever
CONTROL SYSTEMS
5) Install the reverse check cable end, washer and
snap pin to the reverse check lever.
NOTE:
• Take care to install the snap pin in proper direc-
tion.
• Before installing, adjust the reverse check cable.
<Ref. to CS-58, ADJUSTMENT, Reverse Check
Cable.>
6) Install the heat shield cover.
7) Install the rear exhaust pipe and muffler. <Ref. to
EX(H4DOTC)-13, INSTALLATION, Rear Exhaust
Pipe.> <Ref. to EX(H4DOTC)-14, INSTALLATION,
Muffler.>
8) Install the under cover.
9) Install the plate assembly to the vehicle body.
Tightening torque:
18 N·m (1.8 kgf-m, 13.3 ft-lb)
(1) Set the plate assembly to the vehicle.
(2) Temporarily tighten the bolt (A).
(3) Tighten the bolt (B).
(4) Tighten the bolt (A).
(5) Tighten the bolts (C) and (D).
10) Install the harness clamp to the plate assembly.
11) Install the boot and insulator assembly, and se-
cure with a clamp.
12) Install the front cover assembly.
13) Install the console box. <Ref. to EI-54, INSTAL-
LATION, Console Box.>
14) Check that the gear can be shifted accurately
into each gear ranges.
(A) Reverse check cable
(B) Washer
(C) Snap pin
(D) Front side
CS-00224
(B)
(D)
(C)
(A)
AT-01331
CS-00582
(B)
(A)
(C)
(D)
CS-00312
CS-45
MT Gear Shift Lever
CONTROL SYSTEMS
C: DISASSEMBLY
1. 5MT MODEL
1) Remove the lock wires.
2) Remove the rod from lever.
3) Separate the rod and inner boot.
4) Remove the snap ring from the stay.
5) Separate the gear shift lever and the stay.
6) Remove the boot, bushing and snap ring from
gear shift lever.
7) Remove the spring pin, and then remove the
bushing and snap ring.
(A) Lock wire
(A) Rod
(B) Lever
(C) Stay
(A) Snap ring
(A)
CS-00316
(A)
(B)
(C)
CS-00317
CS-00318
(A)
(A) O-ring
(B) Bushing
(C) Snap ring
(A) Spring pin
(B) Bushing
CS-00319
CS-00320
(B)
(A)
(C)
(A)
CS-00060
(B)
(A)
CS-46
MT Gear Shift Lever
CONTROL SYSTEMS
8) Remove the boss from the joint.
9) Remove the bushing and spacer from the boss.
10) Remove the bushing and cushion rubber from
the stay.
2. 6MT MODEL
1) Remove the spring pin from the slider.
2) Remove the slider and spring.
3) Cut the band clip.
4) Remove the reverse check cable from the cable
plate.
(A) Bushing
(B) Spacer
(A) Bushing B
(B) Stay
(C) Cushion rubber
CS-00322
CS-00238
(B)
(A)
(A)
CS-00058
(A)
(B)
(C)
(A) Slider
(B) Spring pin
(A) Slider
(B) Spring
(A) Cable plate
(B) Reverse check cable
CS-00225
(A)
(B)
CS-00226
(A)
(B)
CS-00228
(A)
(B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст