Subaru Legacy III (2000-2003 year). Service manual — part 862
AC-36
HVAC SYSTEM (HEATER, VENTILATOR AND A/C)
COMPRESSOR
4 CYLINDERS:
6 CYLINDERS:
11) Loosen bolts to remove compressor from
bracket.
C: INSTALLATION
1) Install in the reverse order of removal.
2) Replace O-rings on low-/high-pressure hoses
with new ones, then apply compressor oil.
3) When replacing compressor, adjust amount of
compressor oil. <Ref. to AC-29, Compressor Oil.>
4) Charge refrigerant. <Ref. to AC-24, OPERA-
TION, Refrigerant Charging Procedure.>
AC-00291
AC-00292
AC-00293
AC-37
HVAC SYSTEM (HEATER, VENTILATOR AND A/C)
CONDENSER
13.Condenser
A: REMOVAL
1) Using refrigerant recovery system, discharge re-
frigerant. <Ref. to AC-23, OPERATION, Refriger-
ant Recovery Procedure.>
2) Disconnect ground cable from battery.
3) Remove duct (A).
4) Disconnect high-pressure hose (A) and low-
pressure hose (B) from condenser.
5) Remove radiator bracket (A).
6) Remove 2 bolts. While lifting condenser, pull it
out through the space between the radiator and the
radiator panel.
CAUTION:
Be careful not to damage condenser fins. If a
damaged fin is found, repair it using a thin
screwdriver.
If condenser is replaced, add appropriate
amount of compressor oil to the compressor.
<Ref. to AC-29, REPLACEMENT, Compressor
Oil.>
B: INSTALLATION
1) Install in the reverse order of removal.
CAUTION:
Replace O-rings on hoses or pipes with new
ones, and then apply compressor oil. Confirm
that lower guide of condenser has been fitted
into holes on radiator panel.
2) Charge refrigerant. <Ref. to AC-24, OPERA-
TION, Refrigerant Charging Procedure.>
(1) LHD model
(2) RHD model
AC-00289
( A )
AC-00466
( A )
( A )
( B )
( B )
( 1 )
( 2 )
AC-00053
( A )
AC-00295
AC-00343
( A )
AC-38
HVAC SYSTEM (HEATER, VENTILATOR AND A/C)
CONDENSER
C: INSPECTION
1) Confirm that no dust or insects are found on the
condenser fins. Air-blow or flush fins with water as
needed.
2) Confirm that no oil leaks from condenser. If a
failure is found, replace condenser with a new one.
AC-39
HVAC SYSTEM (HEATER, VENTILATOR AND A/C)
RECEIVER DRIER
14.Receiver Drier
A: REMOVAL
1) Disconnect ground cable from battery.
2) Using refrigerant recovery system, discharge re-
frigerant. <Ref. to AC-23, OPERATION, Refriger-
ant Recovery Procedure.>
3) Disconnect pressure switch harness (A).
4) Disconnect pipe (B).
5) Loosen mounting bolts (C) to remove receiver
dryer.
CAUTION:
The receiver drier contains a desiccant. After
disconnecting receiver drier, plug it to avoid
moisture.
If receiver drier is replaced, add appropriate
amount of compressor oil to the compressor.
<Ref. to AC-29, REPLACEMENT, Compressor
Oil.>
B: INSTALLATION
1) Install in the reverse order of removal.
CAUTION:
Replace O-rings with new ones, and apply com-
pressor oil.
2) Charge refrigerant. <Ref. to AC-24, OPERA-
TION, Refrigerant Charging Procedure.>
AC-00296
( A )
( B )
( B )
( C )
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст