Subaru Legacy III (2000-2003 year). Service manual — part 764
VDC-92
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
7
CHECK POOR CONTACT IN CONNECTORS.
Is there poor contact in steering angle sensor?
There is poor contact.
Replace steering
angle sensor.
Repair or replace
steering angle
sensor connector.
8
CHECK VDCCM.
1) Connect connector to VDCCM.
2) Disconnect connector from steering angle
sensor.
3) Measure resistance between steering
angle sensor connector terminals.
Connector & terminal
(B231) No. 1 — No. 2:
Is the measured value within the specified
range?
114 — 126
Ω
9
CHECK POOR CONTACT IN CONNECTORS.
Is there poor contact in steering angle sensor?
There is poor contact.
Replace VDCCM.
<Ref. to VDC-8,
VDC Control Mod-
ule (VDCCM).>
Repair or replace
VDCCM connec-
tor.
10
CHECK TCM.
1) Connect connector to TCM.
2) Disconnect connector from VDCCM.
3) Measure resistance between steering
angle sensor terminals.
Connector & terminal
(B231) No. 1 — No. 2:
Does the measured value exceed the spec-
ified value?
1 M
Ω
11
CHECK POOR CONTACT IN CONNECTORS.
Is there poor contact in steering angle sensor?
There is poor contact.
Replace TCM.
<Ref. to AT-76,
Transmission Con-
trol Module
(TCM).>
Repair or replace
TCM connector.
12
CHECK VDCCM.
1) Connect all connectors.
2) Erase the memory.
3) Perform inspection mode.
4) Read out the diagnostic trouble code.
Are other diagnostic trouble codes being
output?
Other DTC indicated.
A temporary poor
contact.
13
CHECK DIAGNOSTIC TROUBLE CODE.
Is the same diagnostic trouble code as in the
current diagnosis still being output?
Same DTC indicated.
Proceed with the
diagnosis corre-
sponding to the
diagnostic trouble
code.
14
CHECK AT SYSTEM DIAGNOSTIC TROU-
BLE CODE.
Is the AT system diagnostic trouble code is
same as the specification?
DTC 86
Replace steering
angle sensor.
Replace VDCCM.
<Ref. to VDC-8,
VDC Control Mod-
ule (VDCCM).>
Step
Value
Yes
No
VDC-93
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
MEMO:
VDC-94
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
AH:DTC 48 FAULTY ECM — VDCCM COMMUNICATION LINE
DIAGNOSIS:
• EAS communication line is broken or short circuited.
• EAC communication line is broken or short circuited.
TROUBLE SYMPTOM:
• ABS does not operate.
• VDC does not operate.
WIRING DIAGRAM:
VDC00179
C12
A32
F87
56 57
59 60
62 63
65
82 83
80
27
28
25
26
23
24
21
22
19
20
17
18
15
16
13
14
11
12
9
10
7
8
5
6
3
4
1
2
54
55
52
53
50
51
81
48
49
46
47
44
45
78
79
76
77
75
42
43
40
41
74
72
73
70
71
39
37
38
35
36
69
67
68
66
33
34
61
64
31
32
29
30
58
H6
RH4
A24
A24
C11
A33
A25
A25
WO
O
O
LH4
ENGINE
CONTROL
MODULE
B134
B136
A:
:
C:
:
H4
H6
: 4 CYLINDER ENGINE RHD MODEL
: 4 CYLINDER ENGINE LHD MODEL
RH4
LH4
: 4 CYLINDER ENGINE
: 6 CYLINDER ENGINE
H4
H6
: RHD MODEL
: LHD MODEL
R
L
: WITHOUT OBD MODEL
: WITH OBD MODEL
OO
WO
1 2 3
4 5 6
7 8 9 10 11 12 13 14
F96
L
:
F96
R
:
1 2 3 4
5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20
3
R
12
4
11
L
F96
B255
1 2
7
8 9
5
6
3
4
10 11 12
19 20 21
13 14 15 16
17 18
22 23 24
B136
C:
: H6
B134
A:
: H4
1 2
3 4
5 6
7 8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
24 25
26 27 28 29
30 31 32 33
34 35
45
75
EA
C
EAS
VDC
CONTROL
MODULE
F87
VDC-95
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH DIAGNOSIS CONNECTOR
Step
Value
Yes
No
1
CHECK HARNESS BETWEEN ECM AND VD-
CCM.
1) Turn ignition switch to OFF.
2) Disconnect connectors from VDCCM and
ECM.
3) Measure resistance between VDCCM and
ECM.
Connector & terminal
H4 engine RHD without OBD model
(F87) No. 45 — (B134) No. 24:
(F87) No. 75 — (B134) No. 25:
H4 engine RHD with OBD model
(F87) No. 45 — (B134) No. 32:
(F87) No. 75 — (B134) No. 33:
H4 engine LHD model
(F87) No. 45 — (B134) No. 24:
(F87) No. 75 — (B134) No. 25:
H6 engine model
(F87) No. 45 — (B136) No. 12:
(F87) No. 75 — (B136) No. 11:
Is the measured value less than the speci-
fied value?
0.5
Ω
Repair or replace
open circuit
between VDCCM
and ECM.
2
CHECK GROUND SHORT OF HARNESS.
Measure resistance between VDCCM and
ECM.
Connector & terminal
(F87) No. 75 — Chassis ground:
(F87) No. 45 — Chassis ground:
Does the measured value exceed the specified
value?
1 M
Ω
Repair or replace
ground short cir-
cuit between
VDCCM and ECM.
3
CHECK BATTERY SHORT OF HARNESS.
1) Turn ignition switch to ON.
2) Measure voltage between VDCCM and
chassis ground.
Connector & terminal
(F87) No. 75 — Chassis ground:
(F87) No. 45 — Chassis ground:
Is the measured value less than the speci-
fied value?
0.5 V
Repair or replace
battery short cir-
cuit between
VDCCM and ECM.
4
CHECK INPUT VOLTAGE TO ECM.
1) Turn ignition switch to OFF.
2) Connect connector to VDCCM.
3) Turn ignition switch to ON.
4) Measure voltage between ECM connector
and chassis ground.
Connector & terminal
H4 engine RHD without OBD model
(B134) No. 24 (+) — Chassis ground (
−−−−
):
(B134) No. 25 (+) — Chassis ground (
−−−−
):
H4 engine RHD with OBD model
(B134) No. 32 (+) — Chassis ground (
−−−−
):
(B134) No. 33 (+) — Chassis ground (
−−−−
):
H4 engine LHD model
(B134) No. 24 (+) — Chassis ground (
−−−−
):
(B134) No. 25 (+) — Chassis ground (
−−−−
):
H6 engine model
(B136) No. 12 (+) — Chassis ground (
−−−−
):
(B136) No. 11 (+) — Chassis ground (
−−−−
):
Is the measured value within the specified
range?
10 — 15 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст