Subaru Legacy III (2000-2003 year). Service manual — part 658
RS-20
REAR SUSPENSION
LINK REAR
B: INSTALLATION
Install in the reverse order of removal, observing
the following instructions.
CAUTION:
• Using transmission jack, support rear arm
horizontally, install link rear and tighten nuts to
specified torque.
• Tighten nut when installing adjusting bolt.
• Replace self-locking nut.
NOTE:
Check wheel alignment and adjust if necessary.
C: DISASSEMBLY
Using ST-A, B, press bushing out of place.
ST-A, B
20099AE000INSTALLER & REMOVER
D: ASSEMBLY
Using ST-A and ST-B, press bushing into place.
ST-A, B
20099AE000INSTALLER & REMOVER
E: INSPECTION
Visually check link rear for damage or bends.
(1) Rear arm
(2) Transmission jack
RS-00052
( 1 )
( 2 )
RS-00083
ST-A
ST-B
RS-00083
ST-A
ST-B
RS-21
REAR SUSPENSION
SUPPORT SUB FRAME FRONT
9. Support Sub Frame Front
A: REMOVAL
1) Lift-up the vehicle, using support stand to sup-
port rear sub frame.
2) Remove support sub frame front.
B: INSTALLATION
1) Install in reverse order of removal.
Tightening torque:
Support sub frame front to rear arm bracket
80 N·m (8.2 kgf-m, 59 ft-lb)
Support sub frame front to rear sub frame
175 N·m (17.8 kgf-m, 129 ft-lb)
C: INSPECTION
Visually check support sub frame front for damage
or bends.
RS-00088
RS-22
REAR SUSPENSION
REAR SUB FRAME
10.Rear Sub Frame
A: REMOVAL
1) Separate front exhaust pipe and rear exhaust
pipe.
2) Remove rear exhaust pipe and muffler.
3) Remove rear differential.
With T-type
<Ref. to DI-24, REMOVAL, Rear Differential for T-
type.>
With VA-type
<Ref. to DI-41, REMOVAL, Rear Differential for
VA-type.>
4) Disconnect link front from sub frame.
<Ref. to RS-18, REMOVAL, Link Front.>
5) Disconnect link rear from sub frame.
<Ref. to RS-19, REMOVAL, Link Rear.>
6) Disconnect link upper from sub frame.
<Ref. to RS-14, REMOVAL, Link Upper.>
7) Place transmission jack under sub frame.
8) Remove support sub frame front.
9) After removing bolts, remove sub frame and
support sub frame from vehicle body.
B: INSTALLATION
1) Install in reverse order of removal.
2) For installation and tightening torque of rear dif-
ferential.
With T-type
<Ref. to DI-25, INSTALLATION, Rear Differential
for T-type.>
With VA-type
<Ref. to DI-42, INSTALLATION, Rear Differential
for VA-type.>
3) Using transmission jack, support rear arm hori-
zontally and tighten nuts and bolts securing rear
arm, link front, link rear, link upper and shock ab-
sorber.
4) Install support sub frame front.
NOTE:
Check wheel alignment and adjust if necessary.
C: INSPECTION
Check removed parts for wear, damage and
cracks, and correct or replace if defective.
RS-00085
(1) Rear arm
(2) Transmission jack
RS-00052
( 1 )
( 2 )
RS-23
REAR SUSPENSION
HELPER
11.Helper
A: REMOVAL
1) Jack-up the rear part of the vehicle, support it
with safety stands (rigid racks).
2) Using ST, remove helper.
ST
20099AE030
HELPER SOCKET WRENCH
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
32 N·m (3.3 kgf-m, 24 ft-lb)
C: INSPECTION
Check helper for cracks, fatigue or damage.
RS-00087
ST
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст