Subaru Legacy III (2000-2003 year). Service manual — part 980
EI-22
EXTERIOR/INTERIOR TRIM
MUD GUARD
6. Mud Guard
A: REMOVAL
1) Jack-up the vehicle.
2) Remove
screws and clips to remove mud guard.
B: INSTALLATION
Insert hook into body, and tighten it with screw and
clip.
(A) Except OUTBACK
(B) OUTBACK
EI-00296
( A )
( B )
EI-23
EXTERIOR/INTERIOR TRIM
PROTECTOR
7. Protector
A: REMOVAL
1) Except OUTBACK:
NOTE:
Pay attention to the position of clips (a), (c).
(A)
Section A
(B)
Section B
(C)
Section C
EI-00297
A
B
B
A
A
C
A
A
A
A
A
( a )
( b )
( c )
( A )
( B )
( C )
EI-24
EXTERIOR/INTERIOR TRIM
PROTECTOR
OUTBACK:
Remove clip (a) and bolt (b).
NOTE:
Pay attention to the position of clip (C).
(A)
Section A
(C)
Section C
(E)
Section E
(B)
Section B
(D)
Section D
EI-00298
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
D
A
A
A
A
A
A
A
A
A
A
A
B
A
C
A
A
A
D
E
E
E
E
E
E
A
A
( a )
( a )
( b )
( c )
( d )
( A )
( B )
( C )
( D )
( E )
EI-25
EXTERIOR/INTERIOR TRIM
PROTECTOR
2) Attach masking tape to outer perimeter of side
protector. (If original side protector is re-installed,
tape the entire protector.)
3) Insert fishing line [0.8 mm (0.031 in) dia.] (A) be-
tween side protector (B) and vehicle body. Cut (pull
the line) through two-sided tape (C) along side pro-
tector (B) on the body. Using a puller, remove clips
from vehicle body while pulling side protector to-
wards yourself as required.
NOTE:
• To increase adhesive remover strength, leave
two-sided tape on body and side protector.
• If two-sided tape is too thick, use a putty knife to
cut it thin so that adhesive remover is ready for use.
• If two-sided tape is hard to remove, heat to ap-
proximately 40
°
C (104
°
F).
4) Apply an even coat of adhesive remover to the
two-sided tape.
Recommended adhesive remover:
SUMITOMO 3M4000 or equivalent
CAUTION:
Do not apply adhesive remover to lacquer base
coated body panels.
5) Attach plastic wrap (A) to adhesive remover
coated areas and heat to 40 to 60
°
C (104 to 140
°
F)
for 5 to 10 minutes using an infrared lamp (B).
NOTE:
Do not overheat unit plastic wrap is somewhat
whilte.
6) Using a plastic spatula, remove traces of two-
sided tape from body panel.
7) Remove masking tape and clean traces of two-
sided tape using a cloth dampened with white gas-
oline.
8) Similarly, clean traces of adhesive from two-sid-
ed tape on side protector.
NOTE:
Make sure side protector is clean and free of adhe-
sive remover. Clean if necessary.
EI-00153
( A )
EI-00299
A
A - A
( B )
( B )
( C )
( C )
EI-00155
( A )
( B )
EI-00156
( A )
( B )
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст