Infiniti G20 (P11). Manual — part 222
3
CHECK COOLING FAN HIGH SPEED OPERATION
With CONSULT-II
1. Turn ignition switch “OFF”.
2. Reconnect cooling fan relays-2 and -3.
3. Disconnect cooling fan relay-1.
4. Turn ignition switch “ON”.
5. Perform “COOLING FAN” in “ACTIVE TEST” mode with CONSULT-II.
SEF785Z
6. Make sure that cooling fans-1 and -2 operate at higher speed than low speed.
OK or NG
OK
©
GO TO 6.
NG
©
Check cooling fan high speed control circuit. (Go to PROCEDURE B, EC-307.)
GI
MA
EM
LC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0217 COOLANT OVERTEMPERATURE ENRICHMENT PROTECTION
Diagnostic Procedure (A/T Models) (Cont’d)
EC-299
4
CHECK COOLING FAN LOW SPEED OPERATION
Without CONSULT-II
1. Disconnect cooling fan relays-2 and -3.
SEF857X
2. Start engine and let it idle.
3. Set temperature lever at full cold position.
4. Turn air conditioner switch “ON”.
5. Turn blower fan switch “ON”.
6. Make sure that cooling fans-1 and -2 operate at low speed.
SEC163BA
OK or NG
OK
©
GO TO 5.
NG
©
Check cooling fan low speed control circuit. (Go to PROCEDURE A, EC-304.)
DTC P0217 COOLANT OVERTEMPERATURE ENRICHMENT PROTECTION
Diagnostic Procedure (A/T Models) (Cont’d)
EC-300
5
CHECK COOLING FAN HIGH SPEED OPERATION
Without CONSULT-II
1. Turn ignition switch “OFF”.
2. Reconnect cooling fan relays-2 and -3.
3. Disconnect cooling fan relay-1.
4. Turn air conditioner switch and blower fan switch “OFF”.
5. Disconnect engine coolant temperature sensor harness connector.
6. Connect 150
Ω
resistor to engine coolant temperature sensor harness connector.
7. Restart engine and make sure that cooling fans-1 and -2 operate at higher speed than low speed.
MEF613EA
OK or NG
OK
©
GO TO 6.
NG
©
Check cooling fan high speed control circuit. (Go to PROCEDURE B, EC-307.)
6
CHECK COOLING SYSTEM FOR LEAK
Apply pressure to the cooling system with a tester, and check if the pressure drops.
Testing pressure: 157 kPa (1.6 kg/cm
2
, 23 psi)
CAUTION:
Higher than the specified pressure may cause radiator damage.
SLC754A
Pressure should not drop.
OK or NG
OK
©
GO TO 8.
NG
©
GO TO 7.
7
DETECT MALFUNCTIONING PART
Check the following for leak.
I
Hose
I
Radiator
I
Water pump (Refer to LC-10, “Water Pump”.)
©
Repair or replace.
GI
MA
EM
LC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0217 COOLANT OVERTEMPERATURE ENRICHMENT PROTECTION
Diagnostic Procedure (A/T Models) (Cont’d)
EC-301
8
CHECK RADIATOR CAP
Apply pressure to cap with a tester and check radiator cap relief pressure.
SLC755A
Radiator cap relief pressure:
59 - 98 kPa (0.6 - 1.0 kg/cm
2
, 9 - 14 psi)
OK or NG
OK
©
GO TO 9.
NG
©
Replace radiator cap.
9
CHECK THERMOSTAT
1. Remove thermostat.
2. Check valve seating condition at normal room temperatures.
It should seat tightly.
3. Check valve opening temperature and valve lift.
SLC343
Valve opening temperature:
82°C (180°F) [standard]
Valve lift:
More than 8 mm/95°C (0.31 in/203°F)
4. Check if valve is closed at 5°C (9°F) below valve opening temperature. For details, refer to LC-12, “Thermostat”.
OK or NG
OK
©
GO TO 10.
NG
©
Replace thermostat
DTC P0217 COOLANT OVERTEMPERATURE ENRICHMENT PROTECTION
Diagnostic Procedure (A/T Models) (Cont’d)
EC-302
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст