Infiniti QX56 (JA60). Manual — part 977
![](/vehicles/zatt/vend/genn/ginend.png)
TM-210
< DISASSEMBLY AND ASSEMBLY >
DISASSEMBLY
27. Push A/T assembly harness connector.
CAUTION:
Do not damage connector.
28. Remove oil pan and oil pan gasket. Refer to
29. Check foreign materials in oil pan to help determine causes of
malfunction. If the A/T fluid is very dark, smells burned, or con-
tains foreign particles, the frictional material (clutches, band)
may need replacement. A tacky film that will not wipe clean indi-
cates varnish build up. Varnish can cause valves, servo, and
clutches to stick and can inhibit pump pressure.
• If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to
TM-152, "A/T Fluid Cooler Cleaning"
30. Remove magnets from oil pan.
31. If an A/T fluid temperature sensor 2 is attached, disconnect the A/T fluid temperature sensor 2 connector
as shown below.
a. Disconnect A/T fluid temperature sensor 2 connector (A).
CAUTION:
Do not damage connector.
b. Straighten terminal clips (
) to free terminal cord assembly and
A/T fluid temperature sensor 2 harness.
SCIA5022E
SCIA5199E
SCIA5200E
SCIA8124E
![](/vehicles/zatt/vend/genn/oman.png)
DISASSEMBLY
TM-211
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
32. Disconnect output speed sensor connector (1).
CAUTION:
Do not damage connector.
33. Straighten terminal clip (
) to free output speed sensor har-
ness.
34. Remove bolts (A), (B) and (C) from control valve with TCM.
•
: Front
35. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve notch and
manual plate height. Remove it vertically.
36. Remove the A/T fluid temperature sensor 2 or plug as shown below.
a. A/T fluid temperature sensor 2
JSDIA1319ZZ
JSDIA1320ZZ
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8077E
SCIA5260E
![](/vehicles/zatt/vend/genn/gorivr.png)
TM-212
< DISASSEMBLY AND ASSEMBLY >
DISASSEMBLY
i.
Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
ii.
Remove bracket from A/T fluid temperature sensor 2.
b. Plug
i.
Remove plug (1) with bracket (2) from control valve with TCM.
ii.
Remove bracket (1) from plug (2).
SCIA5253E
SCIA5264E
JSDIA1311ZZ
JSDIA1312ZZ
![](/vehicles/zatt/vend/genn/mosinsea.png)
DISASSEMBLY
TM-213
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
iii. RemoveO-ring (1) from plug (2).
37. Remove O-ring from A/T assembly harness connector.
38. Disconnect TCM connectors.
CAUTION:
Do not damage connectors.
39. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
40. Disconnect TCM connector (1) and transmission range switch
connector (2).
CAUTION:
Do not damage connectors.
JSDIA1313ZZ
SCIA5155E
SCIA5447E
SCIA5448E
JSDIA1317ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст