Infiniti QX56 (JA60). Manual — part 970
![](/vehicles/zatt/vend/genn/veewrtry.png)
TM-182
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
3. Connect A/T fluid temperature sensor 2 connector (A).
4. Securely fasten A/T fluid temperature sensor 2 harness with ter-
minal clip
.
5. Install oil pan to transmission case. Refer to
.
6. Connect the negative battery terminal.
7. Refill the A/T with fluid and check the fluid level and for fluid leakage. Refer to
REMOVAL AND INSTALLATION OF PLUG
Removal
1. Disconnect negative battery terminal.
2. Remove oil pan and oil pan gasket. Refer to
3. Remove plug (1) with bracket (2) from control valve with TCM.
4. Remove bracket (1) from plug (2).
5. Remove O-ring (1) from plug (2).
Installation
CAUTION:
SCIA8125E
: Bolt
JSDIA1311ZZ
JSDIA1312ZZ
JSDIA1313ZZ
![](/vehicles/zatt/vend/genn/kiffust.png)
CONTROL VALVE WITH TCM
TM-183
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
After completing installation, check A/T fluid leakage and fluid level. Refer to
.
1. Install new O-ring (1) in plug (2).
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
• O-ring should be free of contamination.
2. Install plug (2) to bracket (1).
3. Install plug (1) [with bracket (2)] in control valve with TCM.
Tighten plug bolt (
) to the specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
4. Install oil pan to transmission case. Refer to
5. Connect the negative battery terminal.
6. Refill the A/T with fluid and check the fluid level and for fluid leakage. Refer to
JSDIA1313ZZ
JSDIA1312ZZ
JSDIA1311ZZ
![](/vehicles/zatt/vend/genn/oumold.png)
TM-184
< ON-VEHICLE REPAIR >
REAR OIL SEAL
REAR OIL SEAL
Rear Oil Seal
INFOID:0000000005148742
REMOVAL AND INSTALLATION
Removal
1. Remove rear propeller shaft. Refer to
DLN-196, "Removal and Installation"
2. Remove transfer from transmission (4WD models). Refer to
DLN-141, "Removal and Installation"
.
3. Remove rear oil seal using suitable tool.
CAUTION:
Do not scratch rear extension assembly (2WD models) or
adapter case assembly (4WD models).
Installation
1. Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
2. Install transfer to transmission (4WD models). Refer to
141, "Removal and Installation"
3. Install rear propeller shaft. Refer to
.
4. Check the A/T fluid level and for fluid leakage. Refer to
"Checking the A/T Fluid (ATF)"
.
SCIA5254E
Tool number
: ST33400001 (J-26082)
WCIA0475E
![](/vehicles/zatt/vend/genn/lid.png)
FLUID COOLER SYSTEM
TM-185
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
FLUID COOLER SYSTEM
Exploded View
INFOID:0000000005268405
Fluid Cooler
Removal and Installation
INFOID:0000000005268406
REMOVAL
1. Remove the radiator. Refer to
CO-15, "Removal and Installation"
.
2. Disconnect the transmission fluid cooler hoses.
3. Remove the transmission fluid cooler.
INSTALLATION
Installation is in the reverse order of removal.
ALDIA0212GB
1.
Radiator
2.
Fluid cooler hose
3.
Fluid cooler
4.
Fluid cooler hose
5.
A/C condenser
Front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст