Infiniti QX56 (JA60). Manual — part 470
![](/vehicles/zatt/vend/genn/thesond.png)
EM-34
< ON-VEHICLE REPAIR >
OIL PAN AND OIL STRAINER
a. Remove the oil pan (lower) bolts in the reverse order as shown
using power tool.
•
: Engine front
b. Insert Tool between the lower oil pan and the upper oil pan.
CAUTION:
• Be careful not to damage the mating surface.
• Do not insert a screwdriver, this will damage the mating
surfaces.
c.
Slide (2) the Tool by tapping (1) its side with a hammer to
remove the lower oil pan from the upper oil pan.
4. Remove the oil strainer from the oil pan (upper).
5. Remove the oil cooler, if necessary. Refer to
LU-12, "Removal and Installation"
6. Remove the oil pan (upper) using the following steps.
a. Remove the oil pan (upper) bolts in the reverse order as shown.
•
: Engine front
b. Remove the oil pan (upper) from the cylinder block by prying it at
the points shown, using suitable tool.
CAUTION:
Do not damage mating surface.
AWBIA0832ZZ
Tool number
: KV10111100 (J-37228)
WBIA0566E
AWBIA0833ZZ
KBIA2468E
![](/vehicles/zatt/vend/genn/tye.png)
OIL PAN AND OIL STRAINER
EM-35
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
7. Remove the O-rings from the oil pump and front cover.
NOTE:
Do not reuse O-rings.
INSPECTION AFTER REMOVAL
Clean the oil strainer.
INSTALLATION
1. Install the oil pan (upper) using the following steps.
a. Apply liquid gasket thoroughly as shown.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
15, "Recommended Chemical Products and Sealants"
.
CAUTION:
Apply liquid gasket to outside of bolt hole for the hole
shown by .
b. Install new O-rings to the oil pump and front cover side.
c. Tighten the bolts in numerical order as shown.
2. Install the oil strainer to the oil pan (upper).
KBIA2469E
KBIA2470E
KBIA2469E
M6
× 30 mm (1.18 in)
: No. 16, 17
M8
× 25 mm (0.98in)
: No. 1, 3, 5, 7, 9, 13, 15
M8
× 45 mm (1.77 in)
: No. 2, 4, 6, 8, 10, 14
M8
× 123 mm (4.84in) : No. 11, 12
PBIC2553E
![](/vehicles/zatt/vend/genn/corsemeputi.png)
EM-36
< ON-VEHICLE REPAIR >
OIL PAN AND OIL STRAINER
3. Install the oil pan (lower).
a. Apply liquid gasket thoroughly as shown.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
b. Tighten the oil pan (lower) bolts in numerical order as shown.
4. Install the oil pan drain plug.
5. Install engine assembly. Refer to
EM-78, "Removal and Installation"
• Do not fill the engine oil for at least 30 minutes after oil pan is installed.
INSPECTION AFTER INSTALLATION
1. Check engine oil level and add engine oil if necessary. Refer to
2. Start the engine, and check for leaks of engine oil.
3. Stop engine and wait for 10 minutes.
4. Check engine oil level again.
KBIA2471E
PBIC2595E
![](/vehicles/zatt/vend/genn/jos.png)
IGNITION COIL
EM-37
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
IGNITION COIL
Exploded View
INFOID:0000000005148993
Removal and Installation
INFOID:0000000005148994
REMOVAL
1. Disconnect the harness connector from the ignition coil.
2. Remove the ignition coil.
CAUTION:
Do not shock ignition coil.
INSTALLATION
Installation is in the reverse order of removal.
1.
Ignition coil
2.
Spark plug
WBIA0796E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст