Infiniti QX56 (JA60). Manual — part 215
BACK DOOR OPENER FUNCTION
DLK-31
< FUNCTION DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Warning Chime Active Conditions
The warning chime uses two types of audio warnings, a friendly chime and a warning chime. The friendly
chime consists of dings lasting 0.66 seconds each immediately followed by the next ding. The warning chime
consists of beeps lasting 0.33 seconds with a pause of 0.33 seconds between each beep.
Reverse Conditions
Operation status
Operation or conditions
Warning chime pattern
When auto operation starts
Power liftgate switch operation
Friendly chime
2 seconds, 3 dings
Remote keyless entry operation
Back door handle switch operation
Back door close switch operation
When reverse operation starts
When reverse request is detected from
power liftgate switch, remote keyless
entry or back door close switch
Friendly chime
1.3 seconds, 2 dings
When obstacle is detected
Warning chime
2 seconds, 3 beeps
Operating at low voltage
While opening or closing
Warning chime
2 seconds, 3 beeps
A/T selector lever not in P position
Back door close operation
Friendly chime
Continuously dings
Back door open operation
Warning chime
Continuously beeps
(until close operation is started)
Type
Overload reverse
Operation covered
Both directions
Detection method
Operation speed and motor current change direction
Pinch strips during back door close operation
Non-reversed area
• For about 0.5 seconds immediately after drive motor operation
starts
• Between full open and approx. 7
° from full open
• Closure operation area (half switch - close switch)
Number of times reverse allowed
One reversal is allowed (if a second obstacle is detected during a
power open or close operation, the door reverts to manual mode).
DLK-32
< FUNCTION DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER FUNCTION
BACK DOOR OPENER SWITCH : Component Parts Location
INFOID:0000000005146885
BACK DOOR OPENER SWITCH : Component Description
INFOID:0000000005146886
1.
BCM M18, M19, M20
(view with instrument panel LH removed)
2.
Back door control unit B55
(view with right rear panel removed)
3. Power liftgate switch M92
4.
Back door warning chime D514
5.
Back door latch D503
Back door and glass hatch switch
assembly (back door switch) D706
6. Pinch strip LH D517
7.
Pinch strip RH D715
8.
Glass hatch ajar switch D707
9. Back door close switch B63
10. Intelligent Key unit M70
(view with instrument panel RH removed)
11. Combination meter M24
ALKIA0966ZZ
Item
Function
Power liftgate switch
Transmits liftgate open operation signal to back door control unit.
Back door control unit
Transmits liftgate open operation to liftgate motor.
Back door close switch
Transmits back door close signal to back door control unit.
Back door handle switch
Transmits back door open signal to back door control unit.
Pinch strip (LH, RH)
While closing, reverses door direction to full open position when an obstacle is in the way.
Back door warning chime
Announces opening and closing of back door.
BACK DOOR OPENER FUNCTION
DLK-33
< FUNCTION DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY
INTELLIGENT KEY : System Diagram
INFOID:0000000005146887
INTELLIGENT KEY : System Description
INFOID:0000000005146888
The Intelligent Key has the same functions as the remote control entry system. Therefore, it can be used in the
same manner as the remote controller by operating the back door open button.
OPERATION DESCRIPTION/BACK DOOR OPEN FUNCTION
• When back door button of the Intelligent Key is pressed, the back door open signal is transmitted from the
Intelligent Key to the back door control unit via remote keyless entry receiver and the Intelligent Key unit.
• When back door control unit receives the back door open request signal, it operates the back door motor
and opens the liftgate.
OPERATION CONDITION
OPERATION AREA
• Operating Range
• To ensure the Intelligent Key works effectively, use within 80 cm range of each door, however the operable
range may differ according to surroundings.
HAZARD AND HORN REMINDER FUNCTION
When doors are locked or unlocked by Intelligent Key. BCM flashes hazard warning lamps as a reminder and
transmits horn chirp signal to IPDM E/R. IPDM E/R sound horns as a reminder.
The hazard and horn reminder has a horn chirp mode (C mode) and a non-horn chirp mode (S mode).
Operating function of hazard and horn reminder
Hazard and horn reminders do not operate if any door switch is ON (any door is OPEN).
How to change hazard and horn reminder mode
With CONSULT-III
DLK-55, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
.
Without CONSULT-III
Refer to Owner's Manual for instructions.
LIST OF OPERATION RELATED PARTS
Parts marked with
× are the parts related to operation.
ALKIA0704GB
Remote controller operation
Operation condition
Operation
Back door open
• Press and hold the back door open button for 0.5 second or more
Back door opens
C mode
S mode
Intelligent Key operation
Lock
Unlock
Back door open
Lock
Unlock
Back door open
Hazard warning lamp flash
Twice
Once
—
Twice
—
—
Horn sound
Once
—
—
—
—
—
DLK-34
< FUNCTION DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER FUNCTION
Remote keyless entry functions
In
te
lli
gen
t K
ey
Ig
ni
tio
n key
Bac
k do
or l
a
tc
h
Bac
k do
or wa
rni
ng ch
im
e
In
te
lli
gen
t K
ey warn
in
g b
uzze
r
CAN c
om
m
uni
ca
tio
n
sy
st
em
Bac
k do
or c
o
nt
ro
l u
n
it
Com
b
ina
tio
n me
ter
Hazard warning
lamp
s
Horns
IPDM
E/
R
Back door open function by remote control button
×
×
×
×
×
×
Hazard and horn reminder function
×
×
×
×
×
×
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст