Infiniti G35 (V35) Sedan. Manual — part 200
![](/vehicles/zatt/tenge/outheneren/hevit.png)
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-17
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000000963876
WORK SUPPORT
DOOR SW-DR
[ON/OFF]
The switch status input from front door switch (driver side)
DOOR SW-AS
[ON/OFF]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[ON/OFF]
The switch status input from rear door switch RH
DOOR SW- RL
[ON/OFF]
The switch status input from rear door switch LH
DOOR SW-BK
[ON/OFF]
NOTE:
The item is indicated, but not monitored.
CDL LOCK SW
[ON/OFF]
Lock switch status received from central door lock switch by power window switch se-
rial link
CDL UNLOCK SW
[ON/OFF]
Unlock switch status received from central door lock switch by power window switch
serial link
KEY CYL LK-SW
[ON/OFF]
Lock switch status received from key cylinder switch by power window switch serial
link
KEY CYL UN-SW
[ON/OFF]
Unlock switch status received from key cylinder switch by power window switch serial
link
TRNK/HAT MNTR
[ON/OFF]
The switch status input from trunk room lamp switch
RKE-LOCK
[ON/OFF]
Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[ON/OFF]
Unlock signal status received from remote keyless entry receiver
Monitor item
[Unit]
Description
Test item
Operation
Description
INT LAMP
ON
Outputs the interior room lamp control signal to turn map lamp and personal lamp ON
(Map lamp switch is in DOOR position).
OFF
Stops the interior room lamp control signal to turn map lamp and personal lamp OFF.
STEP LAMP TEST
ON
Outputs the step lamp control signal to turn step lamp ON.
OFF
Stops the step lamp control signal to turn step lamp OFF.
LUGGAGE LAMP TEST
ON
Outputs the trunk room lamp control signal to turn step lamp ON.
OFF
Stops the trunk room lamp control signal to turn step lamp ON.
Service item
Setting item
Setting
BATTERY SAVER SET
ON*
With the exterior lamp battery saver function
OFF
Without the exterior lamp battery saver function
![](/vehicles/zatt/tenge/outheneren/lakee.png)
BCS-18
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
*: Initial setting
DATA MONITOR
ILL DELAY SET
MODE 1*
45 sec.
Sets delay timer function timer operation time.
(All doors closed)
MODE 2
Without the func-
tion
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
CUSTOM A/LIGHT SET-
TING
MODE 1*
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal operation.)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE 4
Less sensitive setting than normal setting (Turns ON later than normal operation.)
Service item
Setting item
Setting
Monitor item
[Unit]
Description
PUSH SW
[ON/OFF]
The switch status input from push-button ignition switch
ENGINE STATE
[STOP/STALL/CRANK/RUN]
The engine status received from ECM with CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from unified meter and A/C amp. with CAN
communication
KEY SW-SLOT
[ON/OFF]
Key switch status input from key slot
TURN SIGNAL R
[ON/OFF]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[ON/OFF]
TAIL LAMP SW
[ON/OFF]
HI BEAM SW
[ON/OFF]
HEAD LAMP SW1
[ON/OFF]
HEAD LAMP SW2
[ON/OFF]
PASSING SW
[ON/OFF]
AUTO LIGHT SW
[ON/OFF]
FR FOG SW
[ON/OFF]
RR FOG SW
[ON/OFF]
NOTE:
The item is indicated, but not monitored.
DOOR SW-DR
[ON/OFF]
The switch status input from front door switch (driver side)
DOOR SW-AS
[ON/OFF]
The switch status input from front door switch (passenger side)
![](/vehicles/zatt/tenge/outheneren/xing.png)
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-19
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
WIPER
WIPER : CONSULT - III Function (BCM - WIPER)
INFOID:0000000000963877
WORK SUPPORT
*:Factory setting
DATA MONITOR
DOOR SW-RR
[ON/OFF]
The switch status input from rear door switch RH
DOOR SW- RL
[ON/OFF]
The switch status input from rear door switch LH
DOOR SW-BK
[ON/OFF]
NOTE:
The item is indicated, but not monitored.
OPTICAL SENSOR
[V]
The value of exterior brightness voltage input from the optical sensor
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
ON
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
OFF
Stops the tail lamp request signal transmission.
HEAD LAMP
HI
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LO
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
OFF
Stops the high & low beam request signal transmission.
FR FOG LAMP
ON
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
OFF
Stops the front fog lights request signal transmission.
RR FOG LAMP
ON
NOTE:
The item is indicated, but cannot be tested.
OFF
DAYTIME RUNNING LIGHT
ON
NOTE:
The item is indicated, but cannot be tested.
OFF
CORNERING LAMP
RH
NOTE:
The item is indicated, but cannot be tested.
LH
OFF
ILL DIM SIGNAL
ON
NOTE:
The item is indicated, but cannot be tested.
OFF
Service item
Setting
item
Description
WIPER SPEED
SETTING
ON
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
OFF*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
![](/vehicles/zatt/tenge/outheneren/taryoumethth.png)
BCS-20
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000000963878
WORK SUPPORT
*: Initial setting
DATA MONITOR
Monitor Item
[Unit]
Description
PUSH SW
Displays the status of the engine switch (push switch) judged by BCM.
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from unified meter and A/C
amp. with CAN communication.
FR WIPER HI
[OFF/ON]
Status of each switch judged by BCM using the combination switch reading function
FR WIPER LOW
[OFF/ON]
FR WASHER SW
[OFF/ON]
FR WIPER INT
[OFF/ON]
FR WIPER STOP
[OFF/ON]
Displays the status of the front wiper auto stop signal received from IPDM E/R with
CAN communication.
INT VOLUME
[1
−
7]
Status of each switch judged by BCM using the combination switch reading function
Test item
Operation
Description
FRONT WIPER
HI
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to op-
erate the front wiper HI operation.
LO
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
OFF
Stops transmitting the front wiper request signal to stop the front wiper operation.
Service item
Setting item
Setting
HAZARD ANSWER
BACK
LOCK ONLY*
With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the key fob.
UNLK ONLY
With unlocking only
LOCK/UNLK
With locking/unlocking
OFF
Without the function
Monitor item
[Unit]
Description
REQ SW-DR
[ON/OFF]
The switch status input from the request switch (driver side)
REQ SW-AS
[ON/OFF]
The switch status input from the request switch (passenger side)
PUSH SW
[ON/OFF]
The switch status input from the push-button ignition switch
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст