Infiniti EX35. Manual — part 1449

TM-184

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

REVOLUTION SENSOR

- Tighten oil pan mounting bolts to the specified torque in numerical

order shown in the figure after temporarily tightening them. Tighten
necessary oil pan mounting bolts with specified torque.

2WD : Inspection

INFOID:0000000003130628

INSPECTION AFTER REMOVAL

Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
• If frictional material is detected, perform A/T fluid cooler

cleaning. Refer to

TM-143, "Cleaning"

.

INSPECTION AFTER INSTALLATION

Check the following item after completing installation.
• A/T fluid leakage and A/T fluid level. Refer to

TM-141, "Inspection"

.

• A/T position. Refer to

TM-153, "2WD : Inspection and Adjustment"

.

: Vehicle front

JPDIA0021ZZ

SCIA5199E

AIR BREATHER HOSE

TM-185

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

AIR BREATHER HOSE

2WD

2WD : Exploded View

INFOID:0000000003130629

2WD : Removal and Installation

INFOID:0000000003130630

REMOVAL

1.

Remove air cleaner case (RH). Refer to

EM-27, "Exploded View"

.

2.

Remove exhaust front tube and center muffler with power tool. Refer to

EX-5, "Exploded View"

.

3.

Remove exhaust mounting bracket. Refer to

EX-5, "Exploded View"

.

4.

Remove three way catalyst (right bank). Refer to

EX-5, "Exploded View"

.

5.

Remove air breather hose.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:

• When installing an air breather hose, do not to crush or block by folding or bending the hose.
• When inserting an air breather hose to the air breather tube, be sure to insert it fully until its end

reaches the tube bend “R” portion.

• Install air breather hose to air breather tube so that the paint mark is facing upward.
• Ensure clips are securely installed to brackets when installing air breather hose to brackets.
• When inserting air breather hose to air breather box, be sure to insert it fully until its end reaches the

stop.

• Install air breather hose to air breather box so that the paint mark is facing backward.

1.

Air breather box

2.

Air breather hose

3.

Clip

4.

Clip

5.

A/T fluid charging pipe

A.

Air breather tube

JSDIA0142ZZ

TM-186

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

AIR BREATHER HOSE

• Install clip (1) at the paint mark (A).

AWD

AWD : Exploded View

INFOID:0000000003130631

AWD : Removal and Installation

INFOID:0000000003130632

REMOVAL

1.

Remove air cleaner case (RH). Refer to

EM-27, "Exploded View"

.

2

: Air breather hose

3

: Harness

SCIA8268E

1.

A/T fluid charging pipe

2.

Air breather hose

3.

Clip

A.

Air breather tube

JPDIA0717ZZ

AIR BREATHER HOSE

TM-187

< ON-VEHICLE REPAIR >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

2.

Remove exhaust front tube and center muffler with power tool. Refer to

EX-5, "Exploded View"

.

3.

Remove exhaust mounting bracket. Refer to

EX-5, "Exploded View"

.

4.

Remove three way catalyst (right bank). Refer to

EX-5, "Exploded View"

.

5.

Remove air breather hose.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:

• When installing an air breather hose, be careful not to be crushed or blocked by folding or bending

the hose.

• When inserting an air breather hose to the air breather tube, be sure to insert it fully until its end

reaches the tube bend “R” portion.

• Install air breather hose to air breather tube so that the paint mark is facing upward.