Infiniti EX35. Manual — part 1447
TM-176
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
PARKING COMPONENTS
If the contact surface on parking actuator support (1), parking pawl
(2) and etc. has excessive wear, abrasion, bend, or any other dam-
age, replace the components.
INSPECTION AFTER INSTALLATION
Check the following item after completing installation.
• A/T fluid leakage and A/T fluid level. Refer to
• A/T position. Refer to
TM-153, "2WD : Inspection and Adjustment"
.
JPDIA0034ZZ
REAR OIL SEAL
TM-177
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REAR OIL SEAL
2WD
2WD : Exploded View
INFOID:0000000003130620
2WD : Removal and Installation
INFOID:0000000003130621
REMOVAL
1.
Remove exhaust front tube and center muffler with power tool. Refer to
.
2.
Remove rear propeller shaft. Refer to
3.
Remove rear oil seal (1) using a flat-bladed screwdriver (A).
CAUTION:
Be careful not to scratch rear extension assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• As shown in the figure, use the drift [SST: ST33400001 (J-26082)]
(A) to drive rear oil seal into rear extension assembly until it is
flush.
CAUTION:
• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.
1.
Rear oil seal
2.
A/T
Refer to
JSDIA0176ZZ
JPDIA0037ZZ
JPDIA0039ZZ
TM-178
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
REAR OIL SEAL
2WD : Inspection
INFOID:0000000003130622
INSPECTION AFTER INSTALLATION
Check A/T fluid leakage and A/T fluid level after completing installation. Refer to
AWD
AWD : Exploded View
INFOID:0000000003130623
AWD : Removal and Installation
INFOID:0000000003130624
REMOVAL
1.
Remove exhaust front tube and center muffler with power tool. Refer to
.
2.
Remove rear propeller shaft. Refer to
3.
Remove exhaust mounting bracket. Refer to
4.
Remove three way catalyst (right bank). Refer to
5.
Remove front propeller shaft. Refer to
.
6.
Remove transfer assembly from A/T assembly. Refer to
.
7.
Remove rear oil seal (1) using a flat-bladed screwdriver (A).
CAUTION:
Be careful not to scratch adapter case assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Rear oil seal
2.
A/T
Refer to
for symbols in the figure.
JSDIA0177ZZ
JPDIA0038ZZ
REAR OIL SEAL
TM-179
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• As shown in the figure, use the drift [64 mm (2.52 in) dia. commer-
cial service tool] (A) to drive rear oil seal into adapter case assem-
bly until it is flush.
CAUTION:
• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.
AWD : Inspection
INFOID:0000000003130625
INSPECTION AFTER INSTALLATION
Check for A/T fluid leakage and A/T fluid level after completing installation. Refer to
.
JPDIA0040ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст