Infiniti EX35. Manual — part 1446
TM-172
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
PARKING COMPONENTS
8.
Remove tightening bolts for rear extension assembly and trans-
mission case.
9.
Tap rear extension assembly with a soft hammer (A).
10. Remove rear extension assembly (with needle bearing) from
transmission case.
11. Remove bearing race (1) from output shaft (2).
12. Remove output shaft (1) from transmission case by rotating left/
right.
1
: Self-sealing bolt
A
: Bolt
JPDIA0026ZZ
JPDIA0027ZZ
SCIA3431E
JPDIA0057ZZ
JPDIA0028ZZ
PARKING COMPONENTS
TM-173
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
13. Remove parking gear (1) from output shaft (2).
14. Remove seal rings (1) from output shaft.
15. Remove needle bearing (1) from rear extension.
16. Remove parking actuator support (1) from rear extension.
17. Remove parking pawl (with return spring) (1) and pawl shaft (2)
from rear extension.
JPDIA0029ZZ
JPDIA0030ZZ
SCIA6179J
JPDIA0031ZZ
JPDIA0032ZZ
TM-174
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
PARKING COMPONENTS
18. Remove return spring (1) from parking pawl (2).
19. Remove rear oil seal (1) from rear extension using flat-blade
screwdriver (A).
CAUTION:
Be careful not to scratch rear extension.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Do not reuse seal rings and drain plug gasket.
• Apply petroleum jelly to needle bearing and seal rings.
• Insert the tip of parking rod between the parking pawl and the parking actuator support when assem-
bling the rear extension assembly.
• As shown in the figure, use a drift [SST: ST33400001 (J-26082)]
(A) to drive rear oil seal into the rear extension until it is flush.
CAUTION:
• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.
• Refer to the followings installing rear extension assembly.
SCIA6180J
JPDIA0033ZZ
JPDIA0035ZZ
PARKING COMPONENTS
TM-175
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
- Apply recommended sealant (Genuine Anaerobic Liquid Gasket or
equivalent. Refer to
GI-15, "Recommended Chemical Products
.) to rear extension assembly as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc. from
the transmission case and rear extension assembly mounting
surfaces.
- Tighten rear extension assembly bolts to the specified torque.
2WD : Inspection
INFOID:0000000003130619
INSPECTION AFTER REMOVAL
A
: Start and finish point shall be in
the center of two bolts.
B
: 3 – 5 mm (0.12 – 0.20 in)
Sealant
width (C)
: 1.0 – 2.0 mm (0.04 – 0.08 in)
Sealant
height (C)
: 0.4 – 1.0 mm (0.016 – 0.04 in)
JPDIA0036ZZ
1
: Self-sealing bolt
A
: Bolt
JPDIA0026ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст