Infiniti I35 (A33). Manual — part 91
SMT699B
4.
Install lock pin.
I
Make sure that lock pin is flush with case.
SAT313D
5.
Install speedometer drive gear on differential case.
I
Align the projection of speedometer drive gear with the
groove of differential case.
AAT663
6.
Press on differential side bearings.
SAT546F
7.
Install final gear and tighten fixing bolts in a crisscross pattern.
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REPAIR FOR COMPONENT PARTS
Final Drive (Cont’d)
AT-361
SAT181FB
SAT182F
Assembly (1)
NHAT0177
1.
Install differential side oil seals on transmission case and con-
verter housing.
SAT183F
2.
Install parking actuator support to transmission case. Tighten
parking actuator support bolts to the specified torque. Refer to
AT-288.
I
Pay attention to direction of parking actuator support.
SAT039F
3.
Install parking pawl on transmission case and fix it with park-
ing shaft.
4.
Install return spring.
SAT870D
Adjustment (1)
NHAT0178
DIFFERENTIAL SIDE BEARING PRELOAD
NHAT0178S01
1.
Install differential side bearing outer race without adjusting
shim on transmission case.
2.
Install differential side bearing outer race on converter housing.
ASSEMBLY
Assembly (1)
AT-362
SAT008F
3.
Place final drive assembly on transmission case.
4.
Install transmission case on converter housing. Tighten trans-
mission case fixing bolts to the specified torque. Refer to
AT-288.
AAT665
5.
Attach dial indicator on differential case at converter housing
side.
6.
Insert Tool into differential side gear from transmission case
side.
7.
Move Tool up and down and measure dial indicator deflection.
8.
Select proper thickness of differential side bearing adjusting
shim(s).
Suitable shim thickness = Dial indicator deflection +
Specified bearing preload
Differential side bearing preload adjusting shim:
Refer to SDS, AT-386.
Bearing preload:
0.05 - 0.09 mm (0.0020 - 0.0035 in)
SAT010FB
9.
Remove converter housing from transmission case.
10. Remove final drive assembly from transmission case.
11. Remove differential side bearing outer race from transmission
case.
12. Reinstall differential side bearing outer race and shim(s)
selected from SDS table on transmission case.
13. Reinstall converter housing on transmission case and tighten
transmission case fixing bolts to the specified torque. Refer to
AT-288.
SAT188FE
14. Insert Tool and measure turning torque of final drive assembly.
I
Turn final drive assembly in both directions several times
to seat bearing rollers correctly.
Turning torque of final drive assembly (New bearing):
0.78 - 1.37 N·m (8.0 - 14.0 kg-cm, 6.9 - 12.2 in-lb)
I
When old bearing is used again, turning torque will be
slightly less than the above.
I
Make sure torque is close to the specified range.
Preload adapter:
RE4F04B-(J39713)
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Adjustment (1) (Cont’d)
AT-363
SAT332DA
REDUCTION PINION GEAR BEARING PRELOAD
NHAT0178S02
1.
Remove transmission case and final drive assembly from con-
verter housing.
2.
Select proper thickness of reduction pinion gear bearing
adjusting shim using the following procedures.
a.
Place reduction pinion gear on transmission case as shown.
SAT333DA
b.
Place idler gear bearing on transmission case.
c.
Measure dimensions “B” “C” and “D” and calculate dimension
“A”.
A = D − (B + C)
“A”: Distance between the surface of idler gear bear-
ing inner race and the adjusting shim mating surface
of reduction pinion gear.
SAT334DA
I
Measure dimension “B” between the end of reduction pinion
gear and the surface of transmission case.
I
Measure dimension “B” in at least two places.
SAT335D
I
Measure dimension “C” between the surface of idler gear bear-
ing inner race and the surface of transmission case.
I
Measure dimension “C” in at least two places.
SAT336DA
I
Measure dimension “D” between the end of reduction pinion
gear and the adjusting shim mating surface of reduction pin-
ion gear.
I
Measure dimension “D” in at least two places.
I
Calculate dimension “A”.
A = D − (B + C)
ASSEMBLY
Adjustment (1) (Cont’d)
AT-364
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст