Infiniti I35 (A33). Manual — part 135
![](/vehicles/zatt/ltherawowha/yose/prate.png)
Data Monitor Item (Unit)
Data Monitor item selection
Remarks
ECU INPUT
SIGNALS
MAIN SIGNALS
SELECTION
FROM MENU
USV [FL-RR]
(ON/OFF)
—
—
×
Primary-side switch-over solenoid
valve (ON/OFF) status is displayed.
(USV)
USV [FR-RL]
(ON/OFF)
—
—
×
Secondary-side switch-over solenoid
valve (ON/OFF) status is displayed.
(USV)
HSV [FL-RR]
(ON/OFF)
—
—
×
Primary-side switch-over solenoid
valve (ON/OFF) status is displayed.
(HSV)
HSV [FR-RL]
(ON/OFF)
—
—
×
Secondary-side switch-over solenoid
valve (ON/OFF) status is displayed.
(HSV)
V/R OUTPUT
(ON/OFF)
—
—
×
Valve relay operation signal (ON/
OFF) status is displayed.
M/R OUTPUT
(ON/OFF)
—
—
×
Monitor relay operation signal (ON/
OFF) status is displayed.
VDC FAIL SIG
(ON/OFF)
—
—
×
VDC fail signal (ON/OFF) status is
displayed.
TCS FAIL SIG
(ON/OFF)
—
—
×
TCS fail signal (ON/OFF) status is
displayed.
ABS FAIL SIG
(ON/OFF)
—
—
×
ABS fail signal (ON/OFF) status is
displayed.
EBD FAIL SIG
(ON/OFF)
—
—
×
EBD fail signal (ON/OFF) status is
displayed.
FLUID LEV SW
(ON/OFF)
—
—
×
Brake fluid level warning switch (ON/
OFF) status is displayed.
SNOW MODE SW
(ON/OFF)
—
—
×
“OFF” is displayed.
BST OPER SIG
(ON/OFF)
—
—
×
“OFF” is displayed.
M MODE SIG
(ON/OFF)
—
—
×
“OFF” is displayed.
OD OFF SW
(ON/OFF)
—
—
×
“OFF” is displayed.
EBD SIGNAL
(ON/OFF)
—
—
×
EBD operation (ON/OFF) status is
displayed.
ABS SIGNAL
(ON/OFF)
—
—
×
ABS operation (ON/OFF) status is
displayed.
TCS SIGNAL
(ON/OFF)
—
—
×
TCS operation (ON/OFF) status is
displayed.
VDC SIGNAL
(ON/OFF)
—
—
×
VDC operation (ON/OFF) status is
displayed.
×
: Applicable
—: Not applicable
GI
MA
EM
LC
EC
FE
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSIS — INTRODUCTION
VDC
CONSULT-II Functions (Cont’d)
BR-125
![](/vehicles/zatt/ltherawowha/yose/cout.png)
ACTIVE TEST
=NHBR0264S04
Procedure
CAUTION:
I
Do not perform active test while driving the vehicle.
I
Make sure that completely bleed air from the brake sys-
tem.
I
The active test cannot be performed with the ABS warning
lamp on.
1.
Connect the CONSULT-II connector to the vehicle-side data
link connector and start the engine.
2.
Touch “START” on the display.
SFIA2436E
3.
Touch “ABS” and “ACTIVE TEST”.
SFIA0366E
4.
The test item selection screen is displayed.
5.
Touch necessary test item.
SFIA0367E
6.
Touch “START” with “MAIN SIGNALS” line inverted.
SFIA0368E
7.
The active test screen is displayed.
TROUBLE DIAGNOSIS — INTRODUCTION
VDC
CONSULT-II Functions (Cont’d)
BR-126
![](/vehicles/zatt/ltherawowha/yose/omt.png)
SFIA0366E
Solenoid valve
1)
Select each test items without “(ACT)” for the ABS function
active test, and with “(ACT)” for the VDC/TCS function active
test.
2)
Touch “UP”, “KEEP”, and “DOWN” or “UP”, “ACTUATOR UP”,
and “ACTUATOR KEEP”. And check that the solenoid valves
operate as the “Solenoid Valve Operation Chart”. Refer to
Solenoid Valve Operation Chart.
Solenoid valve operation chart
Operation
Without “(ACT)”
With “(ACT)”
UP
KEEP
DOWN
UP
ACTUA-
TOR UP
ACTUATOR
KEEP
FR RH SOL
FR RH ABS SOLE-
NOID (ACT)
FR RH IN SOL
OFF
ON
ON
OFF
OFF
OFF
FR RH OUT SOL
OFF
OFF
ON*
OFF
OFF
OFF
USV [FR-RL]
OFF
OFF
OFF
OFF
ON
ON
HSV [FR-RL]
OFF
OFF
OFF
OFF
ON*
OFF
FR LH SOL
FR LH ABS SOLE-
NOID (ACT)
FR LH IN SOL
OFF
ON
ON
OFF
OFF
OFF
FR LH OUT SOL
OFF
OFF
ON*
OFF
OFF
OFF
USV [FL-RR]
OFF
OFF
OFF
OFF
ON
ON
HSV [FL-RR]
OFF
OFF
OFF
OFF
ON*
OFF
RR RH SOL
RR RH ABS SOLE-
NOID (ACT)
RR RH IN SOL
OFF
ON
ON
OFF
OFF
OFF
RR RH OUT SOL
OFF
OFF
ON*
OFF
OFF
OFF
USV [FL-RR]
OFF
OFF
OFF
OFF
ON
ON
HSV [FL-RR]
OFF
OFF
OFF
OFF
ON*
OFF
RR LH SOL
RR LH ABS SOLE-
NOID (ACT)
RR LH IN SOL
OFF
ON
ON
OFF
OFF
OFF
RR LH OUT SOL
OFF
OFF
ON*
OFF
OFF
OFF
USV [FR-RL]
OFF
OFF
OFF
OFF
ON
ON
HSV [FR-RL]
OFF
OFF
OFF
OFF
ON*
OFF
FRONT SOLENOID
FRONT ABS SOLE-
NOID (ACT)
FR RH IN SOL
OFF
ON
ON
OFF
OFF
OFF
FR RH OUT SOL
OFF
OFF
ON
OFF
OFF
OFF
FR LH IN SOL
OFF
ON
ON
OFF
OFF
OFF
FR LH OUT SOL
OFF
OFF
ON
OFF
OFF
OFF
REAR SOLENOID
REAR ABS SOL-
NOID (ACT)
RR RH IN SOL
OFF
ON
ON
OFF
OFF
OFF
RR RH OUT SOL
OFF
OFF
ON
OFF
OFF
OFF
RR LH IN SOL
OFF
ON
ON
OFF
OFF
OFF
RR LH OUT SOL
OFF
OFF
ON
OFF
OFF
OFF
*: ON for 1 to 2 seconds after the touch, and then OFF
NOTE:
I
If the active test is performed with the brake pedal depressed,
the pedal stroke may be changed. This is a normal condition.
I
“TEST STOP” is displayed 10 seconds after the operation
start.
GI
MA
EM
LC
EC
FE
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSIS — INTRODUCTION
VDC
CONSULT-II Functions (Cont’d)
BR-127
![](/vehicles/zatt/ltherawowha/yose/nnghtrusar.png)
I
After “TEST STOP” is displayed, to perform the test again,
repeat the step 6 of the operation procedure.
VDC OFF indicator lamp
Touch “ON” and “OFF” on the “VDC WARNING LAMP” screen to
check that VDC OFF indicator lamp operates as follows.
Operation
ON
OFF
VDC WARNING LAMP
ON (Lamp ON)
OFF (Lamp OFF)
NOTE:
During the active test when “OFF” on the “VDC WARNING LAMP”
screen is touched, all of the VDC OFF indicator lamp, SLIP indica-
tor lamp, and ABS warning lamp flash once. This is not abnormal.
Motor relay and actuator relay
Touch “ON” and “OFF” on the “ABS MOTOR” screen to check that
the motor relay and the actuator relay operate as follows.
Operation
ON
OFF
MOTOR RELAY
ON
OFF
ACTUATOR RELAY
ON
ON
NOTE:
I
If the active test is performed with the brake pedal depressed,
the pedal stroke may be changed. This is a normal condition.
I
“TEST STOP” is displayed after 10 seconds from the operation
start.
SLIP indicator lamp
Touch “ON” and “OFF” on the “SLIP LAMP” screen to check that
the SLIP indicator lamp operates as follows.
Operation
ON
OFF
SLIP LAMP
ON (Lamp ON)
OFF (Lamp OFF)
NOTE:
During the active test when “OFF” on the “SLIP LAMP” screen is
touched, all of the VDC OFF indicator lamp, SLIP indicator lamp,
and ABS warning lamp flash once. This is not abnormal.
ABS warning lamp
Touch “ON” and “OFF” on the “ABS WARNING LAMP” screen to
check that the ABS warning lamp operates as follows.
Operation
ON
OFF
ABS WARNING LAMP
ON (Lamp ON)
OFF (Lamp OFF)
NOTE:
During the active test when “OFF” on the “ABS WARNING LAMP”
screen is touched, all of the VDC OFF indicator lamp, SLIP indica-
tor lamp, and ABS warning lamp flash once. This is not abnormal.
TROUBLE DIAGNOSIS — INTRODUCTION
VDC
CONSULT-II Functions (Cont’d)
BR-128
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст